Search found 23 matches
- Thu Jun 22, 2023 3:52 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
All working good till now. But this morning I upgraded ETHOS to 1.4.9 from 1.4.8 using the ETHOS Suite. Now I cannot boot to ErskyTX by pressing Rtn and Power. Is there a workaround for this ? Or do I have to reinstall r18 ?
- Fri May 26, 2023 4:13 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Loaded r17d. Ethos came back. Can dual boot. Could bind Rx in erskyTX ACCST and servos working as they should. Initially servo didn't respond. I had expected AETR. Your Mixer screen shows RETA. Realised my mistake. Channel 1 immediately responded to Rudder stick. Booted into ETHOS. Internal Module s...
- Thu May 25, 2023 4:48 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Loaded r17b. Power on starts erskyTX. Version shows r17b. Try to bind X8R ACCST v2.1.0. Same situation as earlier. Rx displays steady half green and half red . No servo movement. Power down and try to start ETHOS through RTN and power switch combo. Nothing starts and screen is dead. Pressing encoder...
- Wed May 24, 2023 12:46 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
- Tue May 23, 2023 10:56 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Went through the steps once more
- Mon May 22, 2023 9:10 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Using Ethos 1.4.8. Their bootloader is 1.4.3. While following the steps at Step 4 after pressing Encoder button or touching 'Yes", nothing happens. Under Vers I get erskyTX-17a. Yes, ran Ethos and moved the Encoder before going back to erskyTX and taking the screenshot. Created Composite size 5...
- Mon May 22, 2023 4:01 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Would you like me to send you a similar. This time running ETHOS on Tandem iInternal ?
- Mon May 22, 2023 3:59 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Screenshot on ETHOS internal ACCST v2 D16
- Sun May 21, 2023 1:25 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Attached zip
- Sat May 20, 2023 5:13 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Don't think previous file was Raw. Cannot attach the file as it says 'cannot attach with extension .raw'
- Sat May 20, 2023 4:23 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Attempted Binding while logging data
- Fri May 19, 2023 2:50 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Value beside TelRxCount changing
Raw logging OFF
Raw logging OFF
- Fri May 19, 2023 11:50 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Dual boot part working fine. In Ethos I have a Model ID 2 on ACCST D16. Bound and connected. Servos moving correctly on my X8R working on ACCST V2.1.0. Shift to ErskyTX. Rx num set to 2 .Protocol ACCST D16. No movement on servos. While attempting to Bind I get a beep every 10 seconds approx. Rx has ...
- Fri May 19, 2023 4:23 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Downloaded r17. All good till Step 5. At Step 6 Composite is created. Total bytes written 5740544. After that cannot scroll down to rename it firmware.bin. Encoder wheel doesn't move anything. Neither Touch. I backout and shut down. On power up getting only ErskyTX. Option of choosing Ethos has gone...
- Thu May 18, 2023 3:49 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Using X20S.No module.Night here now.Shall check first thing tomorrow morning. Hope you won't mind if I referto you as Sir Mike, as Offer Shmuely has so nicely put.
- Thu May 18, 2023 1:52 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Plan to fly on ErskyTX. Had X8R on ACCST v1.x. Flashed it to ACCST V2.1.0. Chose ACCST D16 with 8 Ch on the menu and tried to Bind. Could not.Rebooted to ETHOS and it bound with attached servo working correctly. Is there any special Bind procedure ?
- Wed May 17, 2023 1:46 pm
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Thank you so much. Got it .
- Wed May 17, 2023 6:36 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Not getting that colourful page and cannot change from ACCESS to ACCST(D16). I'll wait for next release from you, and again attempt.
- Tue May 16, 2023 10:01 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
I am getting this screen. Had downloaded r16a.
- Tue May 16, 2023 5:27 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
All my Rxs are ACCST D16 and one is a TD Rx. Do not have any ACCESS Rx. While attempting to choose ACCST in the Protocol menu, I'm offered ACCESS Internal and XJT external. As I don't have a XJT external module fitting the Tandem X20S, is there any way I can use the Internal ACCST capabilities with ...
- Mon May 15, 2023 9:41 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
That's great news. For updating ETHOS can I use the ETHOS Suite ? Or do I have to follow a different procedure ? Thank you for all the fantastic work.
- Mon May 15, 2023 4:32 am
- Forum: erskyTx (was ersky9x)
- Topic: ErskyTx on X20
- Replies: 296
- Views: 782135
Re: ErskyTx on X20
Installed r16a on my Tandem X20S. Not sure if this is a test version. While trying to bind Rx, the only option available is ACCESS. For ACCST, I guess have to get a 4in1 module. Any plans of having TD on this ? Fantastic work. . .
- Tue Oct 11, 2016 4:42 am
- Forum: openTx
- Topic: Documentation for OpenTX 2.2 Taranis and Horus
- Replies: 89
- Views: 227580
Re: Documentation for OpenTX 2.1 and Taranis
Thanks for all your high quality and fantastic work on this much needed documentation.
On your 'Corrections' of Sep 16, I think you meant 2.1.9 but inadvertently typed 2.2.9.
It is people like you who make OpenTX so much worthwhile and so so much better than closed systems.
On your 'Corrections' of Sep 16, I think you meant 2.1.9 but inadvertently typed 2.2.9.
It is people like you who make OpenTX so much worthwhile and so so much better than closed systems.