openrcforums

Are you getting RSSI or Vfas signal ? I only needed 1 wire from smartport to uart TX 3 on my F4 flight controller. Im running an XSR receiver though. Yeah, so it turns out I'm an idiot and the Vfas is reporting the voltage to my TX. :roll: Guess I wasn't looking for the right setting as I'm used to...

I may have originallyposted in the wrong thread as it was for 9XR Pro Hardware... admins please feel free to move my posts if needed but here's my latest telemetry issue. (Screenshots attached to original thread here: http://openrcforums.com/forum/viewtopic.php?f=122&t=10279 ) Been trying to get...

Hi All, Been trying to get telemetry working on my Flip32 F4 board to my Turnigy 9XR Pro w/XJT module. I've posted this a few places looking for help so if you've seen it on another forum I apologize. I've always had good luck with the fellas on this forum though so I figured it wouldn't hurt to ask...

Thanks for the help fellas.
Yeah, I'll have to keep fiddling with it on my 64bit system, but at least for now it's working on the 32bit and I can finally play around with it.

Ok... here's what worked: My Windows 7 Pro 64bit computer would not install drivers for the TX and the eepSkye program still crashed. I was able to get the program to work with my Netbook running Windows 7 Home Premium 32bit and the following steps: 1. I updated my FW on my TX to the ersky9xProvR219...

Ahh... Trainer Switch... Ok, did that, getting USB on the TX screen but PC still can't install the Driver Software and Device Manager is still showing "Unknown Device" under "Other Devices"

I also made sure it's a USB 2.0 port

I do not get USB on the screen... just "Connecting..."

When I look in my Device Manager, it shows 2 Bluetooth Devices that are not loading... is there a setting in the FW that I need to adjust so the system will display the TX as a Storage Device and not a Bluetooth device?

Yeah, they're working. Guess I wasn't pushing hard enough ;-) When you connect the USB, and see "Connecting . . " on the radio display, does the PC show any indication (tones etc.) that a USB device has been connected? Windows 7 64bit (Home) worked fine for me. I've now updated to Windows ...

Ok.... after several attempts, I was able to get into the Maintenance menu (was just being finicky I guess) and update the bootloader to v1.7. I connect the TX via USB and Turn on, open eepSkye that I got from the er9x website and I try to "Read Memory from TX" and "Read Firmware from...

If you have bootloader v1.1, I think you have to power the radio while holding both horizontal trims towards the center of the radio. Only after that you can connect the USB cable. Make sure the USB connector is fully inserted in the radio's USB socket. I've tried both ways, Powering on then pluggi...

So I managed to use just the microSD card to update both the firmware (to r218) and the Bootloader (to 1.7) on my Turnigy 9XR Pro. I apparently did this with the same file (ersky9xr_rom.bin) - that seems pretty bizarre, I would have expected they would be different files (but maybe I just missed th...

In case anyone else is looking for a similar setup.

Following this thread: viewtopic.php?t=8825

I was able to get this setup and running perfectly! Thanks for all the help everyone!!

jhsa wrote:Try this:

CH6 100% CH6
R 100% sIDx Switch (!GEA) (The "R" means it is a replace mix)
CH7 100% CH7
R 100% sIDx Switch (GEA) (The "R" means it is a replace mix)

João

Looks like that worked! The sIDx source was what I needed. Awesome!

Thanks for all the help! [emoji106]

Been trying to mess with this lately and have been able to kind of get it to work on the P1 Pot as the controlling switch, but I need this to work using the 3POS as the controlling switch and haven't been able to figure it out. So for example: If my GEAR switch is in position 1 = ID0, ID1, ID2 contr...

Hi Mike,
It's Revision: 421, Jun 18 2016
I tried the r419 downloaded from the er9x.com site originally but had the same issue.
On the bottom of the screen it'll briefly pop up saying "eeprom data transfer started" then the program crashes.

Hi all, I'm having an issue with Rev. 421 of the eepSKYe program (downloaded from here: http://openrcforums.com/forum/viewtopic.php?f=7&t=4676&p=65894#p65894). I'm using a 9XR Pro running ersky9xr v218 firmware. I can get the TX to connect to the PC (Windows 7 Pro 64bit) and see the 2 connec...

Thanks Kilrah, that's what I'm looking for except I would need the channel to NOT center when being changed, but to stay in the last used position for that channel.

I think I just asked a similar question but was looking to have the 3 POS change channels when a 2 POS is activated. However, I would need the channel to NOT center when being changed, but to stay in the last used position for that channel.

I have a Turnigy 9XR Pro and I'm wondering if this is possible... I'm looking for a way to have the 3 POS affect different channels when a 2 POS is activated or deactivated. So for example, in a DJI Naza system, I'd like the 3 POS to change the Flight Modes on Channel 6 when the Gear Switch is Down....

Hi All, I'm selling my FrSky DJT Telemetry Module with a Futaba Trainer Port cable (for telemetry on 9XR Pro Transmitters). I'd like to get $30 for both the Module and the Cable. Works great, has awesome range and telemetry works as well, I'm just upgrading to an XJT Module and no longer need this. ...

Check the telemetry wire connection on the back of the DJT. It is very easy to offset the connector by mistake João Please check this. As I said, it wouldn't be the first time someone connected the telemetry cable wrong.. João #FACEPALM.... Yep... that was it! Son-of-a... Apparently the slot for th...

The full set of manuals for the 9xr pro is here: http://openrcforums.com/forum/viewtopic.php?f=123&t=5581 I've looked through the manuals, they dont go into much detail about setting up the telemetry systems (they even reference that they don't) and have tried adjusting my settings based on wha...

Not sure if this is where to post this, please feel free to move to the correct thread, but I'm having a helluva time trying to get my Telemetry system working. My setup is: Turnigy 9XR Pro (I've tried both ersky9x-r204 and ersky9xr-r218 Firmware) DJT Module w/the Futaba Trainer Port cable D4R-II RX...

I know this is an old post, but I'm having a helluva time trying to get my Telemetry system working. I have a similar build: Turnigy 9XR Pro (I've tried both ersky9x-r204 and ersky9xr-r218 Firmware) DJT Module w/the Futaba Trainer Port cable D4R-II RX FBVS-01 Sensor I've adjusted my A2 Voltage in th...