Search found 28 matches

by Crusader
Sun May 21, 2017 2:12 am
Forum: erskyTx (was ersky9x)
Topic: SBUS FrSky Telemetry setup?
Replies: 5
Views: 2521

Re: SBUS FrSky Telemetry setup?

Found it,

Thank you for helping this dumb dumb.
much apreciated,

Neil
by Crusader
Sun May 21, 2017 2:05 am
Forum: erskyTx (was ersky9x)
Topic: SBUS FrSky Telemetry setup?
Replies: 5
Views: 2521

Re: SBUS FrSky Telemetry setup?

Hi Mike and Bob,
Thanks for your help. Upgrade of firmware OK.
had Telemetry wire in wrong pin.
can now see Rx and swr levels.
still not sure on where the Ctot etc are setup ??

wil search some more.

Thanks,
Neil
by Crusader
Sat May 20, 2017 10:14 am
Forum: erskyTx (was ersky9x)
Topic: SBUS FrSky Telemetry setup?
Replies: 5
Views: 2521

Re: SBUS FrSky Telemetry setup?

yes and now I am sorry, but i am even more confused, i might upgrade the firmware. yes the telemetry module is in the smart port sorry about that. i had the proto on pmm as soon as i changed it to pxx "no telemetry" says the radio. so i go to the telemetry menu and if i have it on frhub it does not ...
by Crusader
Sat May 20, 2017 7:54 am
Forum: erskyTx (was ersky9x)
Topic: SBUS FrSky Telemetry setup?
Replies: 5
Views: 2521

SBUS FrSky Telemetry setup?

Hi guys, sorry to be here asking questions again. I have a FlySky TH9x with a 9Xtreme board in it running ersky9x. I am trying to setup an FrSky lipo voltage monitor (SBUS) with a X8R receiver. the radio knows there is telemetry as when I turn the receiver off, it complains. But I can not see in the...
by Crusader
Sat Apr 29, 2017 10:22 pm
Forum: Hardware
Topic: Noob Confusion with 9X Calibration and trim Display
Replies: 5
Views: 1487

Re: Noob Confusion with 9X Calibration and trim Display

Thank you guys, yes a new model and others I have setup are all fine?
I will look at the model setup for the one with the issue.
I should have tried a different model before asking, sorry.

Thanks again.
Neil
by Crusader
Sat Apr 29, 2017 8:16 am
Forum: Hardware
Topic: Noob Confusion with 9X Calibration and trim Display
Replies: 5
Views: 1487

Re: Noob Confusion with 9X Calibration and trim Display

Thanks for your reply, No, sorry, more confusion. no they never centre on the bars after a calibration unless I use the trim switches to make them do so. I just thought that after calibration they should line up with the centre? The calibration screen looks centred.. am I doing something wrong or ju...
by Crusader
Sat Apr 29, 2017 5:16 am
Forum: Hardware
Topic: Noob Confusion with 9X Calibration and trim Display
Replies: 5
Views: 1487

Noob Confusion with 9X Calibration and trim Display

Hi All, I'd like to start by saying thanks, for all the mod threads and valuable information that is here on the forums. I have a FlySky TH9X with a 9Xtreme installed multiple 3 way switches, push buttons and sliders. I have also just finished putting in two FrSky M-9 Gimbals after having the Tarani...
by Crusader
Wed Jun 15, 2016 8:03 pm
Forum: 9Xtreme upgrade board
Topic: 9Xtreme V2? Or Discontinued?
Replies: 51
Views: 13408

Re: 9Xtreme V2? Or Discontinued?

I purchased another board, for my wife's 9x, since stocks are low, thanks for the warning :)
by Crusader
Mon Jun 06, 2016 4:02 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

thank you again for your help, I did have a couple of issues.

a broken 5v connector
a dud motor
and I replaced the transistor (was not sure about its integrity).
so I have simplified the installation and cables and it works fine.

I will do some reading as you suggest.


Cheers,
Neil
by Crusader
Sun Jun 05, 2016 2:50 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

Thank you so much for that info. I wasn't sure on how to do that.
I tested it that way, and it now works. Thanks for your help.

Regards,
Neil
by Crusader
Sun Jun 05, 2016 1:10 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

hmmm, and wired in the push buttons.
by Crusader
Sun Jun 05, 2016 1:07 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

I do not get a resistance reading across the pins.. I really do not know? changed out the motors? attached is the haptic screen, should it vibrate on an idle time out? thanks for your help by the way, much appreciated.. I do know a little about electronics,but it always helps to have a second set of...
by Crusader
Sun Jun 05, 2016 12:20 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

Replaced the transistor, tested the ciruit on an external psu and it functions correctly. Attached it to the radio and nothing :( i'm pretty sure i have the software setup for it. But i will check again. :(
by Crusader
Sat Jun 04, 2016 10:58 pm
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

I might replace the transistor and see what happens...
by Crusader
Sat Jun 04, 2016 10:47 pm
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

these are the rectifier diodes I used http://www.ebay.com.au/itm/131625882853?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT yes, I used two of them in series (I have enough to replace them) Signal diodes I used. http://www.ebay.com.au/itm/131587557222?_trksid=p2060353.m2749.l2649&ssPage...
by Crusader
Sat Jun 04, 2016 9:57 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Re: Lost Hapticoutput?

I followed, pretty much, your tutorial. I added some extra plugs for modular connections. I had it working with some smaller motors than the ones you used, but wasn't happy with the force produced. 'I put in the 4 push buttons and replaced the the motors. then things no longer worked. I have 5.1v be...
by Crusader
Sat Jun 04, 2016 6:23 am
Forum: 9Xtreme upgrade board
Topic: 9Xtreme V2? Or Discontinued?
Replies: 51
Views: 13408

Re: 9Xtreme V2? Or Discontinued?

I'd be in for two version 2 boards, i have had heaps of fun with the first one.
but you will need quite a few more to make it worth your while.

love this one, so thank you.
by Crusader
Sat Jun 04, 2016 6:19 am
Forum: 9Xtreme upgrade board
Topic: Lost Hapticoutput?
Replies: 13
Views: 2132

Lost Hapticoutput?

Hi people of the forum,
I have lost haptic feed back on my 9Xtreme board...
what output should I see at pin 12 on the expansion posts.

Regards,
Neil
by Crusader
Fri Jun 03, 2016 5:41 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Those haptic motors are better than the ones I tried first.
by Crusader
Mon May 23, 2016 4:44 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

I have a couple of screws with the same issue, I have ordered some new screws a little larger diameter.
by Crusader
Sat May 21, 2016 6:51 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Thank you so much for this thread João, and to Mike for the software tweaks. I have just hacked the hell out of my FS-th9x with 2 more pots (taranis sliders) 2 x 3 position switches, haptic feed back, just waiting on 4 buttons and 2 more 3 position switches to completely fill it up :lol: it has been...
by Crusader
Tue May 10, 2016 9:06 pm
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Hi João,
Can I please ask one more question?
What size are your haptic motors?
I got some in but they are tiny.. 4 x 8 mm they just don't seem big enough

Regards,
Neil
by Crusader
Tue May 10, 2016 2:03 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Hi João,
That is fantastic information thank you, your responses are very much appreciated.

Regards,
Neil
by Crusader
Mon May 09, 2016 1:09 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Hi João,
Thank you for the links, I will purchase one of those as well.
I already have some coming, I just was not sure if you were using momentary or latching style switches.

Regards,
Neil
by Crusader
Fri May 06, 2016 2:43 am
Forum: 9Xtreme upgrade board
Topic: My 9Xtreme Installation
Replies: 212
Views: 47809

Re: My 9Xtreme Installation

Hi João,
Thank you so much for documenting these this is awesome stuff.
Can I please ask you what type of switches you used for the extra 4 push buttons you installed.

Regards,
Neil
by Crusader
Mon Apr 18, 2016 11:52 pm
Forum: 9Xtreme upgrade board
Topic: Reverse Current Protection Mod for 9xtreme
Replies: 66
Views: 14578

Re: Reverse Current Protection Mod for 9xtreme

Just being nosy here.. I understand why you would remove the bracket, but why removing the regulator, transistor and buzzer? I know they don't do anything, but why the trouble? ;) João From my point of view, I was just asking. I may not remove any of them but depending on what else I was going to d...
by Crusader
Mon Apr 18, 2016 11:40 pm
Forum: 9Xtreme upgrade board
Topic: Reverse Current Protection Mod for 9xtreme
Replies: 66
Views: 14578

Re: Reverse Current Protection Mod for 9xtreme

jhsa wrote:You don't need the regulator on the switch board. also don't need the transistor and buzzer., You can also remove the metal thingy that connects both halves of the radio.. :) ;( :mrgreen:

None is needed..

João

Thanks for the confirmation.

Neil
by Crusader
Mon Apr 18, 2016 11:25 pm
Forum: 9Xtreme upgrade board
Topic: Reverse Current Protection Mod for 9xtreme
Replies: 66
Views: 14578

Re: Reverse Current Protection Mod for 9xtreme

Hello Gents, I am just starting to mod out my FS-TH9X Radio, 9xtreme board in and working great (love this board..) it appears a lot of you are doing this... ---------------------------------------------- I have unsoldered/removed three components: Regulator, Transistor, Buzzer and also I removed th...

Go to advanced search