Search found 709 matches
- Thu Jan 14, 2021 9:13 pm
- Forum: FrSky Taranis radio
- Topic: Voice turning on the X9D Plus SE
- Replies: 12
- Views: 220
Re: Voice turning on the X9D Plus SE
I do not have an X9D Plus SE 2019 , but the version shown indicates that the firmware is for an X9D Plus. ..not an SE or 2019. I'm not sure this is important as I have not downloaded or used the X9D Plus SE 2019 firmware and SD, but believe the label should be OpenTx Plus 2019. Apparently the X9D+SE...
- Thu Jan 14, 2021 7:36 pm
- Forum: FrSky Taranis radio
- Topic: Voice turning on the X9D Plus SE
- Replies: 12
- Views: 220
Re: Voice turning on the X9D Plus SE
It has to have a SD card with the proper contents. Each release of firmware has different version numbers of the contents of the SD, There are some SD cards that are fake that have been reported in some units. These are generally 1 mb cards. So ask seller if the unit has an SD, the size of the cards...
- Mon Dec 07, 2020 5:25 pm
- Forum: Hardware
- Topic: Which receiver for e-glider (Taranis X9D)
- Replies: 5
- Views: 666
Re: Which receiver for e-glider (Taranis X9D)
The V8 series precedes my involvement with FrSky, so I know very little about it. It is an older rf protocol than X series ACCST I use. I believe it supports the older V8 protocol and the somewhat newer D8 protocol. The 2 series receivers I mentioned are D16 rf protocols. Your older tx (like mine) s...
- Sun Dec 06, 2020 10:01 pm
- Forum: Hardware
- Topic: Which receiver for e-glider (Taranis X9D)
- Replies: 5
- Views: 666
Re: Which receiver for e-glider (Taranis X9D)
Your tx does not support ACCESS rf protocol. SO you want an ACCST rx. A RX6R or G-R6X have 6 pwm output pins. The G version has a built in vario. (Some say that vario is not as good as the separate vario.) I use R6XR frequently. There are multiple versions of ACCST. Unless you upgraded your RF board...
- Wed Aug 05, 2020 2:32 pm
- Forum: openTx for FrSky radios
- Topic: Help With Full Span Aileron Rates
- Replies: 3
- Views: 594
Re: Help With Full Span Aileron Rates
Chances are you are using Ail sticks as in your flap mix, use the ail channel instead.
But there are other possibilities.
For best chance of getting help, post your .otx of the model.
But there are other possibilities.
For best chance of getting help, post your .otx of the model.
- Thu Jul 23, 2020 3:54 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Cannot bind X7 with receiver X8R and S8R
- Replies: 3
- Views: 548
Re: Cannot bind X7 with receiver X8R and S8R

On the tx my QX7 shows' D16' on 2.2.4 for internal.
Not sure if this helps.
- Tue Jul 21, 2020 12:58 am
- Forum: openTx
- Topic: Time dependent mixer order
- Replies: 2
- Views: 448
Re: Time dependent mixer order
Mixes are not time dependent !!! Your question is not clear. The best way to show what you are doing is to post an .otx of your model. (Along with what model and make ofthe your tx you are using and what the OpenTX version is.) The stabilizer is looking at both Ch11 and Ch10 except when channel 10 i...
- Thu Jul 09, 2020 9:29 pm
- Forum: General help (FrSky Taranis radio)
- Topic: D6FR Rx binds with Taranis but no telemetry
- Replies: 6
- Views: 1124
Re: D6FR Rx binds with Taranis but no telemetry
For quite sometime, automatic discovery of sensors has not been available. The videos are often out of day. You must use Discover new sensors. If you connected directly to the battery you exceeded the input capability of A2. It expects only 0 to 3.3 V. You may have fried the A2 input circuit. You mu...
- Tue Jun 16, 2020 4:39 pm
- Forum: FRSky Horus radio
- Topic: Converting model from horus10 to 2019 X9D
- Replies: 8
- Views: 1487
Re: Converting model from horus10 to 2019 X9D
All levels of 2.3 should be compatible. I was afraid you had 2.3.x on the X9D 2019 and maybe 2.1.x on the Horus. Are you trying to convert on the tx or in Companion? I don't use a Horus so will not be much help. Good luck, out.
Posting your Horus .otx might be helpful.
Posting your Horus .otx might be helpful.
- Tue Jun 16, 2020 4:09 pm
- Forum: FRSky Horus radio
- Topic: Converting model from horus10 to 2019 X9D
- Replies: 8
- Views: 1487
Re: Converting model from horus10 to 2019 X9D
It is probable that your Operating Systems are not at the same version level. It is even possible your Horus is running FrSkyOs rather than OpenTX. In order for someone to help it would be needed to know these pieces of info. In addition there are some inputs on the Horus that are not available on y...
Re: FreeSky
Did you mean FreeLink? I don't know what FreeSky is other than the way to pronounce FrSky.
- Sun May 24, 2020 2:18 am
- Forum: openTx
- Topic: RadioMaster TX16s: where do I activate LUA and telemetry scripts
- Replies: 22
- Views: 3656
Re: RadioMaster TX16s: where do I activate LUA and telemetry scripts
There are 'switches' which are 2 or 3 position toggle and there are navigation buttons/rotaries that generate EVENTS.
Events are auto updated by the Operating System, Switches must be polled to get current status.
Events are auto updated by the Operating System, Switches must be polled to get current status.
- Fri May 15, 2020 2:49 am
- Forum: General help (FrSky Taranis radio)
- Topic: Can not select luac in radio profile
- Replies: 10
- Views: 1418
Re: Can not select luac in radio profile
I have an X9D and use 2.2.4. I can not reproduce your problem.
I'm on Windows 10.
What PC and version Operating system are you using?
I'm on Windows 10.
What PC and version Operating system are you using?
- Thu May 07, 2020 8:15 pm
- Forum: openTx
- Topic: Horus X10s express and OpenTX
- Replies: 9
- Views: 1708
Re: Horus X10s express and OpenTX
No need to go to 2.3.5.
Going straight to 2.3.7 is fine, it contains all the fixes in 2.3.5 plus new changes.
Going straight to 2.3.7 is fine, it contains all the fixes in 2.3.5 plus new changes.
- Sat Apr 18, 2020 2:32 pm
- Forum: Software
- Topic: I think I've been an idiot, please help
- Replies: 3
- Views: 1214
Re: I think I've been an idiot, please help
Models may still need work. If you started with OpenTX version that was 2 or 3 versions older than 2.3.7. The conversion process provided is good, but generally speaking it is only really reliable to upgrade one step at a time. The format of the model data is stored in generally is changed each time...
- Sun Apr 12, 2020 10:23 pm
- Forum: Software
- Topic: I think I've been an idiot, please help
- Replies: 3
- Views: 1214
Re: I think I've been an idiot, please help
Your SD card needs to be updated with sdcard-212x64-2.3V0026.zip from
https://downloads.open-tx.org/2.3/relea ... tx-x9d%2B/
What version of OpenTx did you have before the update?
https://downloads.open-tx.org/2.3/relea ... tx-x9d%2B/
What version of OpenTx did you have before the update?
- Wed Apr 01, 2020 10:44 pm
- Forum: Software
- Topic: Switch Position Custom Telemetery Display
- Replies: 1
- Views: 2173
Re: Switch Position Custom Telemetery Display
Sorry for the slow response, I thought someone would chime in...then forgot about your request. I don't think I understand what you want, ... or else what you are asking for is not feasible. The screen is only 128x 64 pixels. The smallest size character is 7 pixels high by 5 wide. therefore you can ...
- Sun Jan 26, 2020 3:44 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Is it possible to set up 3 position callouts on RS/LS?
- Replies: 4
- Views: 1958
Re: Is it possible to set up 3 position callouts on RS/LS?
try this and show your special functions for the voice announcements, there are some possibilities of mistakes there.
But better you should understand why.
We can work on this as soon as we arrive at a solution that fulfills your wants/needs.
But better you should understand why.
We can work on this as soon as we arrive at a solution that fulfills your wants/needs.
- Fri Jan 24, 2020 2:35 am
- Forum: General help (FrSky Taranis radio)
- Topic: Saving Trim Settings in Companion
- Replies: 5
- Views: 1930
Re: Saving Trim Settings in Companion
Nothing that is done in the Simulator of Companion is saved. Try just deleting a a mix in the simulator then closing the Simulator and restarting it. The mix will still be there. Nothing done to the model definition gets changed after the compaion simulator section is closed. There is another Simula...
- Wed Jan 22, 2020 9:14 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Is it possible to set up 3 position callouts on RS/LS?
- Replies: 4
- Views: 1958
Re: Is it possible to set up 3 position callouts on RS/LS?
Yes.
A slider is just a pot like S1, S2...
So create 3 logical switches remembering that the pot has values -100 to +100.
Use thes logical switches to set the flap positions mixes and to call out via SF.
A slider is just a pot like S1, S2...
So create 3 logical switches remembering that the pot has values -100 to +100.
Use thes logical switches to set the flap positions mixes and to call out via SF.
- Sun Jan 12, 2020 9:07 pm
- Forum: erskyTx (was ersky9x)
- Topic: "Trainer Connection Lost" error while not using trainer
- Replies: 9
- Views: 2459
Re: "Trainer Connection Lost" error while not using trainer
Why is the model set to 'Slave' if you are not using the radio as a student radio in a trainer setup'?
Set it to 'Master' and try.
Set it to 'Master' and try.
- Tue Jan 07, 2020 4:10 pm
- Forum: General help (FrSky Taranis radio)
- Topic: Flaps and subtrim
- Replies: 2
- Views: 1239
Re: Flaps and subtrim
It is best to set the flaps mechanically to be neutral in the 'up' position of the switch. It can be done with weights but you are then using 1/2 of the servo possible motion and thus putting a heavier load on the servos. You do not say what firmware or transmitter you are using. If you insist on do...
- Sat Jan 04, 2020 3:01 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New beta version of openXsensor (=openXvario)
- Replies: 530
- Views: 125472
Re: New beta version of openXsensor (=openXvario)
Thank you very much
- Sat Jan 04, 2020 2:19 am
- Forum: OpenXVario - an open source vario supported by the open source firmwares!!
- Topic: New beta version of openXsensor (=openXvario)
- Replies: 530
- Views: 125472
Re: New beta version of openXsensor (=openXvario)
Can you please post the URL to github for OpenXsensor.
TIA
(Maybe put it in post 1 so it would be easy to find for new folks.)
TIA
(Maybe put it in post 1 so it would be easy to find for new folks.)
- Thu Jan 02, 2020 5:11 pm
- Forum: Software
- Topic: Telemetry and OpenTx 2.3.4 Companion.
- Replies: 7
- Views: 2632
Re: Telemetry and OpenTx 2.3.4 Companion.
I'm with you on doing setup, initial checking and fixes via a real keyboard/mouse/full size display and simulation on Companion. Companion is the reason that I started to think of trying OpenTX. I like the ability to see more of the big picture than my QX7 or X9D screens show. I had stayed with the ...
- Thu Jan 02, 2020 1:30 am
- Forum: Software
- Topic: Telemetry and OpenTx 2.3.4 Companion.
- Replies: 7
- Views: 2632
Re: Telemetry and OpenTx 2.3.4 Companion.
It is a known problem. The developers are concentrating on the tx side for safe flying for us and there are several new txs being supported. I believe that there is no developer that is concentrating solely on Companion. For this reason I am staying with 2.2.4. Unless you have a new tx with ACCESS t...
- Sat Dec 28, 2019 12:05 am
- Forum: General help (FrSky Taranis radio)
- Topic: Total Newbie
- Replies: 1
- Views: 1371
Re: Total Newbie
Do you mean aranis 9XD plus SE 2019? If so: There are two protocols supported by the Taranis 9XD plus SE 2019. So you will want to by either the new Archer series receivers or ones that are ACCST/D16 and the latest models of these. RX4R, RX6R, G-RX8R and G-RX6R are all compatible with the D16 protoc...
- Wed Dec 25, 2019 5:33 pm
- Forum: other
- Topic: Control stepper motors with radio control
- Replies: 1
- Views: 3712
Re: Control stepper motors with radio control
More information is required. What transmitter and receiver are you using? (Make and model.) What is the name and version number of the firmware on the transmitter? Do you have two channels, one for each stepper motor/DRV8825? It is not obvious to me that the DRV8825 would support a reverse function...
- Thu Dec 05, 2019 9:16 pm
- Forum: openTx
- Topic: Open Tx Simulator problem
- Replies: 3
- Views: 1307
Re: Open Tx Simulator problem
Wow, you are correct.
I have no idea what "Dock in Main Window" is supposed to do, but I doubt it is supposed to close Companion when it closes.
I think you uncovered a bug.
I checked out on X9D and QX7, and it behaves the same. It is not Jmpr T16 unique.
I have no idea what "Dock in Main Window" is supposed to do, but I doubt it is supposed to close Companion when it closes.
I think you uncovered a bug.
I checked out on X9D and QX7, and it behaves the same. It is not Jmpr T16 unique.
- Thu Dec 05, 2019 8:27 pm
- Forum: openTx
- Topic: Open Tx Simulator problem
- Replies: 3
- Views: 1307
Re: Open Tx Simulator problem
If you mean changes you made while in the simulator started from Companion, It is normal to not save changes made by the simulator.
What PC are you using and what operating system.
This did not occur for me on Windows 10 with Conpanion 2.3.RC1
What PC are you using and what operating system.
This did not occur for me on Windows 10 with Conpanion 2.3.RC1