openrcforums

Yes Mike lua is displayed. However, I cannot test the function.
splash is always present after turning it on several times.
the change was worth it, thanks, greetings Siegi

Hi Mike, I installed the new software with eepskye in the first step. Splash works! then I checked the version, all correct P1 r224. Then I searched for Lua, not available! Control of the bits in the PC, only 499!! why? step2, software installed with companion, same picture. Lua is missing, only 499...

Hi Mike,
I'm trying it out, but it may take a while.
greet Siegi

I didn't want to do without the greeting, I think it's so nice, I don't need lua, so I reinstalled the old firmware.
Due to the last update of the erskyTX test versions, the differences from B1 r223 to B5 r223 are no longer visible. Can you break this down for me again?
Thanks greetings
phil

Hi Mike, I downloaded the new software r 223 bin, it has 622 KB. my old r233 B5 has 499 KB. where are the differences, I could not find anything. I could not start the firmware from the bootloader, but with Companion. Can it be that the start picture doesn't come up anymore? Immediately after the sp...

Hi Mike,
I think it's good to be able to adjust the colors. that upgrades your system a lot.
the arrows on the side are for the new touch display, great.
say hello to Siegi

Hi Mike,
with the module in the external slot, the RX setting works perfectly. The No Module feature isn't that important either, so the effort doesn't justify it.
it is important that the erskyTX software remains clear and works well.
Thanks for that, regards Phil

internal module deactivated, but was set with RX, then switched off.
external module switched on indicates setting of internal module with multi RX. a RX change causes a white field. When the module is plugged into the external slot, the RX are displayed

Hi Mike, in my experiments with the multiprotocol module, I used the 2nd slot of the TX16S. I saw that in the protocol setting, shaft 2, the RX of shaft 1 is displayed under multi. so far good, but if I want to select another RX, the RX display disappears. I can no longer see and select RX. greeting...

Thanks Mike
for the info.
phil

Hello Mike, please answer my question about the potential loss of bond. Is that possible?
phil

can it be that the bond has been lost? no model was bound! It was not possible to re-bind with the existing data! only when I had reinstalled the program erskyTx could I bind again. That means all models I have to enter it manually, copying memory into it didn't work either. I suspect the "loss of l...

Thanks Mike,
it works fine if a light switch is specified.
I am always amazed how familiar you are with this system.
stay healthy, greetings Phil

thanks Mike for the quick reply.
My taranis x9d, without plus, does not go into light mode with SLAVE.

Hi Mike, because of my grandson i went into coach mode yesterday. Plant taranis d, erx9d-B5r223. when clocking through src: jack PPM etc. the screen suddenly went dark. I don't get in bright anymore. When the control is switched on, the screen is normally bright and then goes into dark mode. I've tr...

das ist schön Mike dass du etwas Farbe in erskytx bringst. Vermutlich wird es noch einige Zeit dauern bis die ersten Screens fertig sind.
vielen Dank
Phil

Hello Mike,
the program runs very well so that the erskyTx file could be entered on the er9x -erskyTx homepage.

greeingst Siegi

As far as I know, this module can only store one recipient. if you have a second recipient you have to tie it again and again.
a multi-protocol module provides a remedy
phil

hello Mike can the height sensor be seen on this file?

Hi Mike,
it took some time. I had to see how it works with the raw file.
logging with cat1 worked, I hope you can do something with the data. Greetings Siegi

Hi Mike,
in october last year we had contact about the height sensor cat01. We couldn't activate it at the time and display the altitude.
In the new TX16S with the latest software, the transmitter shows the altitude with opentx, but not with erskyTx. what can be the reason?
greetings Siegi

attached are the screens with erskyTX.
LS and RS do not run in parallel

Thanks for the information. I noticed that with the A9r 223 software the RS signal was lost. The error was eliminated in the B3r 223 software. the slider direction RS should be reversed so that when the button points upwards the bar also deflects upwards. For the optics, it would be nice if some dis...

there is always something new for me. Suddenly the power lamp from the Radiomaster shows "green" and not red. Firmware: erskyTx is from March 19, so the latest version. What has changed?
that's great!

Hi Mike,
I noticed that the two lateral rotary valves SL and SR do not run synchronously. I've tried a lot but haven't made it. Do you have a guy there?
lovely Easter Phil

There are things that one does not understand. before I could restart the transmitter I removed the erskyTx programs from the SD card. after the restart I loaded again via eePskye erskyTx. There is no erskyTx on the bootloader, and there is no erskyTx on the SD card either, although I operate the tr...

Hi Mike,
my joy in experimenting is a little clouded. for me the software 223A9 in color with logical key assignment would be sufficient. This software is clear and quick to adapt and easy to use.
thank you phil

studying the video of bardwell, radiomaster bricked. 1. PC with driver for DFU, impulseRC 2. Transmitter without battery 3. Connection of PC to transmitter 4. loaded with companion software opentx Very important The transmitter must be without a battery, no success with the battery connected. it too...

he is working again, has cost nerves!
i am happy

unfortunately I was unable to repair the transmitter. i watched help videos and tried everything.
the fault is probably in the motherboard.