Search found 7 matches
- Fri May 25, 2018 8:13 pm
- Forum: openTx
- Topic: Setting half of an input to two different outputs
- Replies: 1
- Views: 2482
Setting half of an input to two different outputs
Hi guys. So I'm building a home made rc car just for fun and I'm doing a tank design where the left side spins to go one way and the right side spins to go the other. The way I'd like to do this on my QX7s is that elevator up will make both sides rotate the same way which is easy enough. The hard pa...
- Fri Mar 04, 2016 2:02 am
- Forum: openTx
- Topic: Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
- Replies: 2
- Views: 2050
Re: Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
I got it working. It turned out my resister had issues I dunno. I replaced it and now it works for the most part. I've only noticed one big difference from my apm 2.5 board. On the current mode tab it says MSG FS OFF 953. The 953 goes up and down by 3 or 4 and beeps every time it does this. No idea ...
- Tue Mar 01, 2016 12:13 am
- Forum: openTx
- Topic: Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
- Replies: 2
- Views: 2050
Re: Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
Just an update. With my apm 2.5 I plug the flight controller telemetry tx directly into the rx on my 9xr and the mavlink shows up fine. Everything is good. I set up my PX4MINIAIO and hook up the ftdi to the tx and rx and connect to mission planner at 19200 and everything is fine. This confirms I hav...
- Sun Feb 28, 2016 5:53 pm
- Forum: openTx
- Topic: Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
- Replies: 2
- Views: 2050
Mavlink on 9xr working with apm 2.5 not with PX4MINIAIO V1.3
Hi guys. I'm trying to hunt down the cause of this issue. I have a apm 2.5 that I can hook directly up to my 9xr and have telemetry data show up. I'm trying the same thing with my PX4MINIAIO V1.3 and I get nothing. Everything is 19200 baud rate. I tried uart1 and 2 on the PX4MINIAIO. I'm assuming it...
- Thu Jan 07, 2016 5:22 pm
- Forum: openTx
- Topic: How do I set alarms on Mavlink data on my 9xr
- Replies: 1
- Views: 1647
Re: How do I set alarms on Mavlink data on my 9xr
Mods can remove this. I posted in the mavlink post. I didn't see it right before I made this post. Thanks.
- Thu Jan 07, 2016 12:47 pm
- Forum: openTx
- Topic: [MAVLINK] Input needed for MAVLINK ArduPlane / ArduCopter.
- Replies: 60
- Views: 53503
Re: [MAVLINK] Input needed for MAVLINK ArduPlane / ArduCopter.
Hello all. I just got mavlink on my 9xr using ulrs. Is it possible to set alarms for mavlink data? I can't find a way to do so.
- Thu Jan 07, 2016 12:38 pm
- Forum: openTx
- Topic: How do I set alarms on Mavlink data on my 9xr
- Replies: 1
- Views: 1647
How do I set alarms on Mavlink data on my 9xr
Hi guys. My first question is that is it possible to set alarms on Mavlink data? If so how is that done? For instance, if my voltage is dangerously low I want to change the flight mode.