openrcforums

I have tried all the combinations of everything in this thread. I get receiver/transmitter numbers when I reverse the wires on what is being talked about on page 1. Maybe my settings inside the controller are off? I am using the same setup that works with the d4r II I'm no expert by any means, but ...

I personally have no idea what a Lua script is so I can't answer that. Yes, there have been updates. You can return to the product page and check the "updating firmware" tab for details. Thanks for the firmware info. I am new to LUA scripts as well. Just heard of it when I got the anysens...

Hi guys, I am wondering if it is possible to use Lua Scripts on the 9xtreme with ersky9x? I bought an anysense telemetry module and this module has lua scripts made for Taranis. https://github.com/cemizm/TaranisLuaScripts I am wondering if I can use it for the 9xtreme as well? Also it has been some ...

s_mack wrote:As is? No. With some wiring cleverness of that connector? Still probably not, but it depends on the current demands of the monitor. I suspect it is far too high.

Cool, just wanted to know. Thanks for the quick reply. I guess I will just stick a lipo to the back of the monitor.

Thanks again.

Hi,

Is it possible to power something like a FPV monitor off of the 9x using the barrel connector at the side? I am using the Turnigy 9x with 9xtreme board.

Thanks.

Measure with a ohm meter between the orange wire and either the red or the brown wires while you move the stick. If the resistance changes between about 0 and about 2.5K, then it is non amplified. I believe they don't sell the amplified ones anymore anyway.. I measured it and it was 500 to 2.5K, is...

Hi,

I just received my FrSky gimbal from hobbyking, how do I tell if they are the amp version or non amp version? I am using 9xtreme board would there be any fitting issues?

With the XJT, the black wire soldered there is all you need.. Better put a connector in between though, so you can separate both halves of the radio when opening it.. As far as the DJT is concerned, it depends. Is it modded? If so, how? But if you have a XJT, you won't need the DJT as the XJT can w...

jhsa wrote:Please look at the picture
Forget the text at the bottom.
João

Thanks João for the quick reply.
So I just solder the black wire there? How about the other wire? I think it is the white wire.

And also does this work with XJT and also DJT? Thanks.

kaznad: You do still need to connect the black wire for the telemetry to pin 5 (bottom pin) of the module connector. Mike. Oh, I was under the impression that the XJT you dun need to connect the wire. So I have to drill a hole and connect it to the outside of the module? Is there anyway without dri...

Have you set the protocol to PXX, not PPM, and D8 mode? Mike. Hi Mike, I tried setting the protocol to PXX and the type to D8. I still cannot get telemetry. I was able to get it to work in terms of controls, but no telemetry. In the telemetry menu I went to Custom Display 1 and choose RSSI and Batt...

Hi, I have the 9xtreme on my 9x, I used to have a DJT module but was told I needed to route wires to the back of the module to get telemetry. I also read somewhere that the XJT module works without any modification. I bought an XJT module but it doesn't seem to have any telemetry data. I am using it...

Do you mean the sticks (Inputs) by AIL, ELEŢHR and RUD? I'm Asking because this is how the switches are represented. Sticks are Ail, Ele, Thr and Rud.. So, you want to program triple rates then? Please download the manual linked below and read pages 41 to 43. Expo/DR screen. This is the manual for ...

Of course. What exactly you want to do? João For example, I want to set switch ID0 with AIL,ELE,THR and RUD with limits of 40% for all of them. I want to set switch ID1 with AIL,ELE,THR and RUD with limits of 60% for all of them. I want to set switch ID0 with AIL,ELE,THR and RUD with limits of 100%...

Hi,

I've been struggling to get this heli up and flying. Can someone post the config file for HCP80V2 for use with HT8 please? Thanks a lot.

Hi,

Is it possible to set ID0, ID1 and ID2 with different limits? Similar to those toy quadcopter transmitters where there is a low, medium and high settings?

Thanks.

1. See: http://openrcforums.com/forum/viewtopic.php?f=7&t=7715#p102758 . 2. The SD card stores the voice files, and may also be used to log telemetry data. Newer firmware may either be flashed directly to the processor, or placed on the SD card and flashed from there. Mike. Wow, you can flash f...

just received my 9xtreme and i must say well done on the quality of the kit i like it alot. so without instructions and not much knowledge ( i have previously only soldered up a small cable to let me flash er9x through usbasp ) i decided to put it all together and it is very straight forward i must...

Unfortunately not. As we are using a STM processor, when you plug the USB in with power off it starts in the STM ROM bootloader. This is selected by a hardware signal, while on the Atmel processor on the 'PRO uses an internal programmable fuse to select this. Mike. Ah that did it. I din know it has...

How do you connect the 9Xtreme board to the eePskype software? Without turning on the radio, I plugged in the USB cable. Nothing happened. Screen blank. In eepe when I click Read Memory from TX I got Tx disk not mounted. I am thinking I need drivers for the 9xtreme board? Where should I download the...

I'm not sure if this will help. But here is a picture of the components together. I have already installed everything so unfortunately I cannot measure for you. But what I can tell you is that it fits snugly behind the screen. Just by looking at the picture in hobbyking site, I would say the 9xtreme...

Thank you everyone. I've downloaded the file Voice Pack 9XR-Pro 16Khz.zip.

So do I just dump the zip file in the root folder of the SD card? Or should I unzip it to the root folder of the SD card. Thank you.

Hi,

I had the CR1220 batt in date/time now stays. Have a 1GB card in there, able to detect when on bootloader mode.

So where do I download the voice files? Noob here so bare with me please. Sorry.

Hi,

It says new version of ERSKY9x (ersky9x9XT_rom.bin) is available (r217) when I try to download it. It says error downloading file not found. Thanks.

Hi Mike,

I'm using the FrSky DJT module. Thanks for the info on the sdcard and copy via USB.

Where can I download eepskye? Thanks again.

Hi, I joined this forum just to discuss on the 9xtreme board. :D Installed the board on my x9, works great. Some things I notice is, the wires are really good quality, the connectors are little tight but that is good as it wun come off easily. And remember to get the CR1220 batt and install it befor...