openrcforums

Hi Mike,

Amazing!
Thank you for your support.

Xavier

Hi Hubert,

Thank you, I have completely forgot the first rule "RTFM" !

Kind regards,
Xavier

Hi Mike, Also I have two possibilities. 1) Hardware modification with bottom PIN TX Connector connected to M64 PE0-MOSI (just 1 wire direct with no inverter) with the following options #define TELEMETRY -> Enable #undef MULTI_STATUS -> Disable #define MULTI_TELEMETRY -> Enable #undef INVERT_TELEMETR...

Hi Mike, Thank you for your answer and sorry for my response time. This is great news! I'm going to try the last ER9x version this weekend. Just another question to be. Do I just need to configure the MPM with #define ENABLE_SERIAL -> Enable Serial #undef ENABLE_PPM -> Disable PPM OR do I also need ...

Hi, First thank you for the extraordinary work. I haven't find an answer for my question. I have mod an "old" Turnigy 9x V2 with just a connector to flash the M64 and flash with the last er9xProv822n version. I have a Multiprotocol Bangood DIY ATmega 328P flash with the last release v1.3.1...

Hi @RightRudder It is two different bootloader. TinySafeBoot : The one I use with ATtiny and ATmega and it work one Linux and Windows, command line. (Link: http://jtxp.org/tech/tinysafeboot_en.htm ) AVRootloader : Work just with ATmega and on Windows (João reference) (Link: https://github.com/damadm...

Hi, Just an off topic about the 1 wire bootloader. Why don't use the TinySafeBoot ( http://jtxp.org/tech/tinysafeboot_en.htm ) ? I have already use it on attiny85 with success. It is simple, but without a gui, you must use the command line. I have try it with Linux, but it will be work with Windows ...

Hi,

Thank you!
You are faster than lucky luke! I'll try it when I can (not this week-end, perhaps next week) and I say you the result.

Xavier

Hi, @mstrens I have in stock this reference : NTC 100k 1% 3950 (also used to my 3d printer). I can send you one NTC if you will try it. I found a simple library here. It will be for generic NTC (with beta, R) like your oXs code and not just fix to one NTC type. https://github.com/panStamp/thermistor...

Hi, I know that oXs can read an voltage input and use an IC (already did it), but the maximal temperature is about 150°C and I will measure 250°C-300°C. Sorry, I have perhaps write a too short question, I know how works a NTC. But I want to know if you plan to integrate possibility of table for NTC ...

Hi,

@mstrens
Do you have already plan to support temperature sensor built with a NTC in oXs 8?

BR
Xavier

HI,

Nice! I must buy on GY-86 ASAP

Thanks!
Xavier

Hi,

OK I don't know about that.
The first once without DFU it has not work on my computer.
I'll know for the next time, I don't use it and save me 10 sec to not install it!

BR
Xavier

Hi, It is a very good job this OpenXSensor! Just a question about the hardware support, do you plan to support the module "IMU 10DOF - MPU6050 gyro & accelerometer + HMC5883 magnetometer + MS5611 altimeter" (12$) , because it's almost the same price as a MS5611 alone and you have the I...

Hi, It works also good for me without any adjustment for companion and Taranis. Do you have install the right version (32 or 64 bits) AND also the dfu util ? 64BITS : http://www.open-tx.org/2013/09/25/dfu-util-07-for-ubuntu-1204-64bit/ OR 32BITS : http://www.open-tx.org/2013/09/25/dfu-util-07-for-ub...