Search found 25 matches
- Mon Mar 06, 2017 3:51 pm
- Forum: openTx
- Topic: Telemetry voltage alarm adj for 3S & 4S with gear switch
- Replies: 12
- Views: 7111
Re: Telemetry voltage alarm adj for 3S & 4S with gear switch
Did somebody find a solution for 3S and 4S alarms without physical switch (so openTx knows whar LiPo was used)?
- Thu Feb 18, 2016 7:48 pm
- Forum: er9x
- Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
- Replies: 598
- Views: 319572
Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Hi hirnsal! I have board Pro mini 328P and only programer USBASP. Can I upload hex file to Board over USBASP without Bootloader program and whill runing corect of function voice program? My Board have working on 16MHz too. Someone has the program as skatch file for Arduino? Also you need Arduino Pro...
- Mon Dec 14, 2015 4:22 pm
- Forum: Turnigy 9XR PRO radio
- Topic: 3pos switch mod and OpenTX
- Replies: 4
- Views: 3887
Re: 3pos switch mod and OpenTX
Yes, 2x -> 3xjhsa wrote:I think he means the real 3 Position mod..
Thank you.jhsa wrote:I don't know opentx but I guess it doesn't support any extra hardware. Again I'm just guessing..
I need to think more about this conversion.
If I will do it it means that I am should use ER9X only
Best,
afon
- Mon Dec 14, 2015 9:42 am
- Forum: Turnigy 9XR PRO radio
- Topic: 3pos switch mod and OpenTX
- Replies: 4
- Views: 3887
3pos switch mod and OpenTX
HI All
Will I be able to use OpenTX after 3pos switch mod?
Will all switches work correctly in OpenTX?
Best,
afon
Will I be able to use OpenTX after 3pos switch mod?
Will all switches work correctly in OpenTX?
Best,
afon
- Fri Nov 13, 2015 6:59 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
-del-
- Fri Nov 13, 2015 6:47 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Рш João Check also the connector's pins are not bridged on the other side of the board. That happened recently on another board.. I guess it is not simple short circuit between connectors, because it was tested with digital multimeter in "Diode test and connectivity check" mode Best, Dmitry
- Fri Nov 13, 2015 6:45 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
HI All Here are some more tests I just did: Only Blue (AIL) removed [table=border:1px solid #888888;padding:3px;][tr=] [td=border:1px solid #888888;padding:3px;] ID Up: [/td] [td=border:1px solid #888888;padding:3px;]ID1: 0[/td] [td=border:1px solid #888888;padding:3px;]ID2: 0[/td] [td=border:1px so...
- Thu Nov 12, 2015 10:19 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
As far as I can see with my magnifying glass the is no bridge between 67-68.
But I did not check other side of PCB.
Dmitry
But I did not check other side of PCB.
Dmitry
- Thu Nov 12, 2015 10:01 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike
I did all tests with radio on/off during adding new wires.
3 Out
ID1:1, ID2:0
+blue
AIL Up: AIL:0, ID1:0, ID:0
AIL Down: AIL:1, ID1:1, ID2:0
+gray
GEAR Up/Down - OK, other are always 0
+orange
Problem as it was described before.
Best,
Dmitry
I did all tests with radio on/off during adding new wires.
3 Out
ID1:1, ID2:0
+blue
AIL Up: AIL:0, ID1:0, ID:0
AIL Down: AIL:1, ID1:1, ID2:0
+gray
GEAR Up/Down - OK, other are always 0
+orange
Problem as it was described before.
Best,
Dmitry
- Thu Nov 12, 2015 7:59 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
AIL up
ID Up: yes
ID middle: no
ID down: no
Ail Down
ID Up: no
ID middle: no
ID down: no
Connection was tested by digital multimeter in "Diode test and connectivity check" mode.
ID Up: yes
ID middle: no
ID down: no
Ail Down
ID Up: no
ID middle: no
ID down: no
Connection was tested by digital multimeter in "Diode test and connectivity check" mode.
- Thu Nov 12, 2015 7:52 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Let me check. Result will be in 5 min.KAL wrote:Seems to me like blue and grey are linked together?Klaus
MfG, Dmitry
- Thu Nov 12, 2015 7:36 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
I have a strong feeling that something wrong with ID switch.
Do you feel the same?
Unfortunately I do not have right now spare switch to check my idea.
Do you feel the same?
Unfortunately I do not have right now spare switch to check my idea.
- Thu Nov 12, 2015 7:28 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
AIL switch down
ID TOP
Orange (Top ID): 3.01V
Grey (Bottom ID): 0.00V
Blue (Bottom AIL): 0.01V
ID Middle
Orange (Top ID): 3.01V
Grey (Bottom ID): 3.14V
Blue (Bottom AIL): 3.14V
ID Bottom
Orange (Top ID): 0.00V
Grey (Bottom ID): 3.12V
Blue (Bottom AIL): 3.14V
Best,
Dmitry
ID TOP
Orange (Top ID): 3.01V
Grey (Bottom ID): 0.00V
Blue (Bottom AIL): 0.01V
ID Middle
Orange (Top ID): 3.01V
Grey (Bottom ID): 3.14V
Blue (Bottom AIL): 3.14V
ID Bottom
Orange (Top ID): 0.00V
Grey (Bottom ID): 3.12V
Blue (Bottom AIL): 3.14V
Best,
Dmitry
- Thu Nov 12, 2015 7:22 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi João! It seems also to me that the green and grey wires are swapped. The blue should be correct on AIL? You can try swapping them and see if it fixes the problem. I swap those two wires and got MORE strange result that was definitely not correct. At least without swapping my GEAR switch shows cor...
- Thu Nov 12, 2015 7:12 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike! Battery voltage: 12.16V Please set the ID switch to ID1 (middle) and the AIL switch UP. Now measure the voltage between the black wire and each of the Orange, Grey and Blue wires. You should see about 3.3V. Orange (Top ID): 3.01V Grey (Bottom ID): 0.01V Blue (Bottom AIL): 0.00V Switch the I...
- Thu Nov 12, 2015 9:36 am
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike! As far as I can see the switches are wired OK. As far as I can see at least two wires go to wrong switches: one for ID and another one for GEAR. I am not sure about TRN and AIL wires because at this moment I have only pictures (I am in office right now and my radio at home). Can you please ...
- Wed Nov 11, 2015 8:27 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike!
Here are 2 photos of connector and switches. I guess GEAR and ID wires were mixed (according to this diagram: 9XR Pro Wiring)
Best,
Dmitry
Here are 2 photos of connector and switches. I guess GEAR and ID wires were mixed (according to this diagram: 9XR Pro Wiring)
Best,
Dmitry
- Wed Nov 11, 2015 6:07 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
It will be nice if you do this mod for all switches that can be converted to 3 position switch.MikeB wrote: A small change I need to do is make this display as ID^, ID- and IDv as a single entry.
- Wed Nov 11, 2015 9:30 am
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike!
radio is completely new, it was delivered from HK 2 days ago and was never opened or modified by me.
I will take pictures (of two switches and connector) and post them here.
Is it OK that ID0 is absent at DiagSwitch menu?
Best,
Dmitry
radio is completely new, it was delivered from HK 2 days ago and was never opened or modified by me.
I will take pictures (of two switches and connector) and post them here.
Is it OK that ID0 is absent at DiagSwitch menu?
Best,
Dmitry
- Tue Nov 10, 2015 7:36 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
Re: ID 0/1/2 switch
Hi Mike! Here are all combinations of AIL and ID switches. Also I took video for you: https://www.youtube.com/watch?v=FMq8IaGWkLY [table=border:1px solid #888888;padding:3px;][tr=] [td=border:1px solid #888888;padding:3px;] AIL OFF (up)[/td] [td=border:1px solid #888888;padding:3px;] ID up[/td] [td=...
- Tue Nov 10, 2015 2:51 pm
- Forum: Turnigy 9XR PRO radio
- Topic: ID 0/1/2 switch
- Replies: 33
- Views: 14763
ID 0/1/2 switch
Hi All I have a question about ID0/1/2 switch. When I turn on my radio with switch in the middle (or low) position I can see "Check your switches warning" with ID0 highlighted there. But when I am trying to test switches at "diagnostics" page (setup section of radio menu) I can s...
- Mon Nov 09, 2015 9:28 am
- Forum: er9x
- Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
- Replies: 598
- Views: 319572
Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Hi all!
Here is my version of ArduVoice-9X based on SMD PCB for ArduSound layout.
First test: https://www.youtube.com/watch?v=7pMFtAroRAk
Final result: https://www.youtube.com/watch?v=mSIFyKOeDcM
Here is my version of ArduVoice-9X based on SMD PCB for ArduSound layout.
First test: https://www.youtube.com/watch?v=7pMFtAroRAk
Final result: https://www.youtube.com/watch?v=mSIFyKOeDcM
- Thu Aug 27, 2015 8:26 pm
- Forum: Turnigy 9XR radio
- Topic: PPM Frame size
- Replies: 23
- Views: 22892
Re: PPM Frame size
Hi Mike.
Thank you very much. Your answer really helped me to understand underlying settings.
I will leave PPM Frame size "as is" (22.5ms)
Thank you very much. Your answer really helped me to understand underlying settings.
I will leave PPM Frame size "as is" (22.5ms)
- Thu Aug 27, 2015 5:40 pm
- Forum: Turnigy 9XR radio
- Topic: PPM Frame size
- Replies: 23
- Views: 22892
PPM Frame size
Hi All, I have Turnigy 9XR + FrSky DJT + FrSky D4R-II D4R-II was flashed with 27ms firmware because I want to use 7 channels. My question is: what PPM frames size should be set in TX settings (openTx or er9x)? At this moment in my TX settings I have (by default) PPM Frame 22.5ms 300u Negative Is it ...
- Tue Aug 25, 2015 11:52 am
- Forum: er9x
- Topic: Version confused
- Replies: 3
- Views: 3513
Re: Version confused
Hi All, Please help be because I am little bit confused with ER9X versions. I have Turnigy 9XR with Atmega128. Also I installed FrSky telemetry mod. And I am not sure what kind of mod is it (here is some photos from mod manual) http://forum.rcdesign.ru/uploads/posts/1/0/5/1/1/3/693031.thumb?d=136121...