openrcforums

Thats the screen I have renamed my model MODEL_01 but I cant find the screen
Phil

If you use a 30 second countdown as a wave file and "play track" when the motor starts, it would free up a timer which could to do the slot time
I edited a one minute count dowm MP3 and coverted it to wave file, or you could record your own
Phil

on my Taranus plus it works best with no delay on logical switch and the function set to 3s channel 10 is set to 200% with 200% offset the value is read off chn 11 getting its value from 10 but only 50% I can now move the slider slowly and still get a reading I will change it to 5% to give flap valu...

Magic!! but does not work if I move the slider slowly, V2 needs a value of 0.1, i can get over it by increasing the weight on channel 10 to 200% then using another ch to divide down
Thanks
Phil

My left hand slider lowers the flaps on my model and it reads out the amount 1 to 100%, but I only want it to read the amount when I alter it.
Is there a way to do this with open TX?
I have a high channel getting its value from the slider and play value contolled by a switch at the moment
Phil

Thanks for all the help I have downloaded the DFU proram and installed it, also Exracted the bin file I now have the FRsky and Open TX loaded Mike it was calibration, I had full max on servos with centre sticks I will save the bin file you extracted for me I did see a graph on one of the screens, it...

All I wanted is for someone to send me the original bin file that came with the taranis plus I Know I should have backed it up but I didn't, so now I can't restore it I don't have the tools, drivers or skill needed. the FRsky site is unhelp full it just tells you to copy the dfu file to the sd card,...

Its a screen with a graph on it, It could display any of the logged items
all I want is the bin file that came with the TX the one I failed to backup
Phil

No, they are 100% out, I have just looked all the outputs are +100%
calabrating will not solve the missing log screen
I need the factory bin file
Phil

Thanks forthe reply
Yes I put in OpenTX taranis plus with companion 2.0.12
I can only get -50% travel on the servos and my log screen is no longer there
I want the factory firmware bin file
Phil

I have used Companion to update my TX, I failed to back up the factory firmware,
It now does not work properly.
could someone send me the correct bin firware file or tell me where I can find it
The one on the FRsky site is a dfu file
Phil

For some time I have tried to find out what this setting is

I found this and I am still baffled

"Drex: taking into account formatting handle, otherwise the gross order from the handle is used"

Can someone make it easier to understand? is it something to do with dual rates?

Phil

How about conecting the haptic motor to the display light via a solid state relay?
one of the switches could be used to turn it off.
Phil

I can alter haptic strength on the setup page
On the fuction page I get the same haptic pulse when I select 1, 2 or 3 in the right hand column
I would like three diffent pulse lengths
Phil

v2.00-fws
open9x-r 1379
v212

Thanks, I have trimmed the file to 1 min, removed some of the numbers and made it a wave file
it's at http://www.glos-mfc.co.uk/phil/1min.wav

I found another set of files at http://www.rmsadenver.com/f3j_announcements.htm
Phil

Does anybody have a 1 minute countdown audio file?
I would like it for F3J: 1 minute, 50 secs, 40s, 30, 25, 15,10,9, 8,7,6,5,4,3,2,1,0
I have an SD card fitted
Phil

Most models need a bit of down elevator compensation, one of mine needs 40% down when I lower the flaps
just add two mixes, use max as source and ID1 & ID2 to switch in the elevator mixes, I highlight the mix amount and adjust the mix while flying
Phil

I have loaded r1103, it has cured the memory proplem, thanks it is great to get it fixed

How many times a day do I need to updated
Phil

I am still using V2.00-fv open9x-r936 Eeprom v209 do I need to load r1110? I have deleted the crashed model, when I load another model using 325 bytes of memory, I have 465 bytes of free on the screen, if I trim this drops to 210. Am I safe to fly? Can I save save and reload my models after update t...

I have noticed that the memory is used up by altering the trims,. I tried a simple model using 140 units of memory with 120 free, altering the trims reduced the memory to 60 but model continued to work with no warning. I did get a low memory warning when I switched on again. I found Open9X great unt...

I have just repoducded, the memory was on 210 and when the fault occured it went to zero. Scseen says 'EEPROM WARNING EEPROM overflow press any key' operating the trms bring the error back pressing any key does not clear the error sitching off and on does not clear the error, 210 units of memory has...

gbirkus wrote:Please post your board type, firmware type, firmware options and version number. Also post your EEPROM and which one model was loaded. We try reproduce it!
Gabriel

V2.00-fv
open9x-r936
Eeprom v209

model 4 using about 350 of memory

PHIL

Which board, which firmware, which version? 124bytes remaining? That's far too low! Especially with a model using Flight Phases and a lot of mixes! It's a long time I didn't test myself the Low EEPROM alarm. My guess right now would be that you were trimming, ran into a "Low EEPROM" alarm...

Rob Thomson wrote:Can you give any info on the firmware version you are running?

V2.00-fv
sun oprn9x-r936

phil

On Sunday the controls on my model locked- no reponse. the tramsmitter had the word EEPROM on the main screen. I tried to switch it off and back on but did not have time as all the switches had to be reset first. The only odd thing was the memory was on Zero it was reading 124 the last time I added ...