Search found 94 matches
- Fri Jan 10, 2014 12:14 pm
- Forum: companion9x
- Topic: Unable to flash new firmware
- Replies: 1
- Views: 3026
Re: Unable to flash new firmware
I'm able to back the eeprom up to the HD, and I can flash the firmware if I uncheck backup and restore eeprom. It finishes with Samba errors, but seems to be successful. Then I can restore my eeprom from the file. Also with errors, but seems to work. Unable to use the simulator at all. Anyone? Sent ...
- Fri Jan 10, 2014 1:58 am
- Forum: companion9x
- Topic: Unable to flash new firmware
- Replies: 1
- Views: 3026
Unable to flash new firmware
I'm hoping someone will be able to help me. I've asked about this issue several times, many months ago, but I've never been able to get it resolved. I am unable to flash new firmware or load eeprom into Companion. I can save it it a file, but it acts like it isn't completely finished, it goes to 96%...
- Wed Jul 17, 2013 12:12 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
I have tried uninstalling and reinstalling Samba and replacing the tclib file from the wiki. No changes. There must be some kind of issue with the board. I've never run anything other than Open9x /OpenTx and it's always been fine. I guess I need to open it up and try a reset. I'm reluctant because e...
- Fri Jul 12, 2013 1:30 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
I just discovered that if I save the eeprom to a file, I am able to open from that file even though it only says it only completed 98%. I'm just afraid to then try to burn it back to the TX because I'm worried something will fail and render my TX useless until I figure this out.
- Fri Jul 12, 2013 12:56 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
OK. I uninstalled then reinstalled SAMBA and unzipped the latest tcl_lib file from the Wiki. I am getting the exact same result as posted above. When I try to read eeprom form TX, it gets to 98% and stops. I still can't use C9x for anything. I also tried eepskye with the same result. Everything was ...
- Tue Jul 09, 2013 7:17 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
I'm on W7. How do I get the output log?
- Tue Jul 09, 2013 5:07 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
I just tried eepskye. Same thing. When I try to read eeprom to a file, I get a read error. It finishes to about 95%.
- Tue Jul 09, 2013 3:54 pm
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Re: Please help with C9x and OpenTX
Showmaster, you're talking about someone else's radio. You helped me with this one before I got the Sky board.
Mine is currently working, I just can't read the eeprom in C9x I get an error when flashing too, but it seems to flash anyway.
Hopefully we can both get things straightened out.
Mine is currently working, I just can't read the eeprom in C9x I get an error when flashing too, but it seems to flash anyway.
Hopefully we can both get things straightened out.
- Tue Jul 09, 2013 11:24 am
- Forum: Software
- Topic: Please help with C9x and OpenTX
- Replies: 25
- Views: 13789
Please help with C9x and OpenTX
I tried posting this in the C9x forum but no one has responded. I'm hoping someone can help me. I'm unable to flash firmware or read my eeprom. This is a recent problem. I hadn't updated my firmware in a month or two and when I did, I also updated C9x. I had a little trouble flashing the latest firm...
- Mon Jul 08, 2013 8:44 pm
- Forum: companion9x
- Topic: Problem with C9x
- Replies: 0
- Views: 1877
Problem with C9x
I have a FlySky 9x with a Sky9x board. I recently updated to the latest versions of OpenTx and C9x. I'm not sure which is causing my problems. When I try to read my eeprom, the process finishes to about 96% and then fails. I had the trouble while trying to update OpenTx, but it seems to have worked ...
- Mon Feb 25, 2013 12:30 pm
- Forum: openTx
- Topic: open9x-r2129
- Replies: 103
- Views: 33550
Re: open9x-r20xx
I'm using the latest version. Still the same behavior. I always keep the freshest version installed.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Mon Feb 25, 2013 11:58 am
- Forum: openTx
- Topic: open9x-r2129
- Replies: 103
- Views: 33550
Re: open9x-r20xx
I'm still having an issue where center beeps kill all sounds until I restart the TX. Any chance that will be fixed?
viewtopic.php?t=2520
Sent from my DROID BIONIC using Tapatalk 2
viewtopic.php?t=2520
Sent from my DROID BIONIC using Tapatalk 2
- Tue Feb 19, 2013 2:23 pm
- Forum: openTx
- Topic: Programming Audio in Open9X
- Replies: 32
- Views: 14682
Re: Programming Audio in Open9X
I'd like to see a description of how to set up voice with telemetry like battery voltage, timers, RSSI, etc. I'm having some trouble with that and it seems difficult to find much information about setting it up.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Wed Jan 30, 2013 12:51 pm
- Forum: The Pickled Gnu (The Pub)
- Topic: why not clover leaf antenna for Tx?
- Replies: 46
- Views: 30792
Re: why not clover leaf antenna for Tx?
I started my research because I am setting my quad up for FPV. I don't need too much range, but more is always better and goes a long way to boost confidence. Some of the threads I read said that you only need to replace one of the antennas for greatly improved range, but both is better. I was think...
- Tue Jan 29, 2013 8:47 pm
- Forum: The Pickled Gnu (The Pub)
- Topic: why not clover leaf antenna for Tx?
- Replies: 46
- Views: 30792
Re: why not clover leaf antenna for Tx?
I've been reading about this exact topic today! It seems that many people have replaced the RX antennas with a pair of Clover Leaf antennas and a Skew Planer Wheel on the TX (might be reversed). People are claiming 2 to 3 times the range and no issues during high bank turns. Might have to give it a ...
- Tue Jan 08, 2013 10:42 am
- Forum: openTx
- Topic: Possible Bug?
- Replies: 4
- Views: 3898
Re: Possible Bug?
Center beep in think is constantly interrupting the playback. Does the issue occur if you love the pot just off center so it does not want to beep? Sent from my Nexus 7 using Tapatalk 2 No problem until the center beep plays. I'll try to upload a video and my eeprom when I get home from work if it ...
- Tue Jan 08, 2013 3:41 am
- Forum: openTx
- Topic: Possible Bug?
- Replies: 4
- Views: 3898
Possible Bug?
I'm not sure where to post this since I don't know if the problem is the board, the software, me, or my SD card, so I'll just put it here and see what happens. I am using the latest version of Open9x and a Sky9x board (not the newest one but one of the latest of the older ones). I've been trying to ...
- Mon Jan 07, 2013 2:42 am
- Forum: companion9x
- Topic: Help, can't use simulate mode c9 (OK, Now)
- Replies: 12
- Views: 8104
Re: Help, can't use simulate mode c9 (OK, Now)
Interesting. Hope it gets sorted. No big deal though.
Thanks
Sent from my DROID BIONIC using Tapatalk 2
Thanks
Sent from my DROID BIONIC using Tapatalk 2
- Sun Jan 06, 2013 9:48 pm
- Forum: companion9x
- Topic: Help, can't use simulate mode c9 (OK, Now)
- Replies: 12
- Views: 8104
Re: Help, can't use simulate mode c9 (OK, Now)
I'm having the same problem here too. Also using Open9x and the Sky9x rev B.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Sat Jan 05, 2013 1:47 am
- Forum: openTx
- Topic: Turnigy open9x & Dji naza configuration
- Replies: 15
- Views: 12838
Re: Turnigy open9x & Dji naza configuration
Thanks Kilrah!! I got everything working! Now I just need to figure out how to set voice files to be triggered by the A2 output on my FrSky module. I want a voice alarm for low flight pack battery. Any suggestions?
- Fri Jan 04, 2013 1:26 pm
- Forum: openTx
- Topic: Turnigy open9x & Dji naza configuration
- Replies: 15
- Views: 12838
Re: Turnigy open9x & Dji naza configuration
I could really use a little help with programming my TX for use with NAZA and GPS too. I am using the latest version of C9x (as a side note, I cannot get the tx simulator to work in this version) and a Sky9x board. I am trying to program a failsafe switch that will work in either GPS or ATTI mode. O...
- Sat Oct 20, 2012 7:28 pm
- Forum: er9x / gruvin9x / th9 based firmwares
- Topic: Using LP5DSM as buddy box
- Replies: 8
- Views: 6908
Re: Using LP5DSM as buddy box
For 2 person control couldn't you just hook the camera stuff to the LP5DSM receiver? Then you wouldn't be connected by a cord.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Fri Oct 05, 2012 2:46 am
- Forum: openTx
- Topic: Playing a song (ersky9x board)
- Replies: 67
- Views: 27534
Re: Playing a song (ersky9x board)
I want "danger zone" to play when the throttle is above 80%.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Thu Oct 04, 2012 11:45 am
- Forum: openTx
- Topic: open9x-r1439
- Replies: 65
- Views: 31947
Re: open9x-r1439
I'm using the Sky9x board and Open9x. Is there a way to use a pot to scroll through the menus? I could do it in Er9x.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Mon Oct 01, 2012 7:53 pm
- Forum: openTx
- Topic: FrSky voltage sensor
- Replies: 9
- Views: 6504
Re: FrSky voltage sensor
Nevermind. Everything's working correctly now. Thanks
- Mon Oct 01, 2012 4:43 pm
- Forum: openTx
- Topic: FrSky voltage sensor
- Replies: 9
- Views: 6504
Re: FrSky voltage sensor
I have the same sensor soldered to the 3s pad connected to the A2 port of a DBR II Plus RX. When I set the max voltage to 19.8v and offset at 0, 19.8 volts is always displayed regardless of the battery voltage. I'm using a 3s battery. I'm using Open 9x 1379 with a Sky9x board. Am I doing something w...
- Tue Sep 25, 2012 10:28 pm
- Forum: DSM2/DSMX Mods
- Topic: Will bind but no control
- Replies: 6
- Views: 9723
Re: Will bind but no control
I've had similar problems with Spektrum. Never going back. I'd put more confidence in the cheap FlySky stuff.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Thu Sep 13, 2012 8:21 pm
- Forum: FRSky Telemetry Mods
- Topic: Using FrSky module with Sky9x board
- Replies: 1
- Views: 2674
Re: Using FrSky module with Sky9x board
Use as-is.
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2
- Thu Sep 13, 2012 3:06 pm
- Forum: General Information & Rules
- Topic: Forum Sections & Sub Clasification
- Replies: 28
- Views: 19556
Re: Forum Sections & Sub Clasification
I forgot to mention in my previous post that the Wiki is great for a lot of stuff and I'm glad to see all of the updates.
Also, maybe we could add a classifieds section for buying and selling boards, parts, services, etc.
Sent from my DROID BIONIC using Tapatalk 2
Also, maybe we could add a classifieds section for buying and selling boards, parts, services, etc.
Sent from my DROID BIONIC using Tapatalk 2
- Thu Sep 13, 2012 11:51 am
- Forum: General Information & Rules
- Topic: Forum Sections & Sub Clasification
- Replies: 28
- Views: 19556
Re: Forum Sections & Sub Clasification
I am pretty sure that most people just use the. "View unread" option. That way I just see everything :-) Sent from my Nexus 7 using Tapatalk 2 Yeah, I guess that's what Tapatalk does, I just haven't used that feature on the PC. I'm almost always looking at the forum on my phone. Thanks Se...