Search found 1513 matches

by ReSt
Fri Jun 21, 2019 5:29 pm
Forum: RF MODULES
Topic: Fried (?) Stock turnigy 9X module (Vbat pin reversal)
Replies: 2
Views: 187

Re: Fried (?) Stock turnigy 9X module (Vbat pin reversal)

If you use the stock rf module, maybe this picture can help you to check the voltages.
There is one more regulator (3.3V) on the rf board
https://www.rcgroups.com/forums/attachm ... id=4444012

Reinhard
by ReSt
Thu Jun 13, 2019 8:03 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Use sticks not for servo position but for servo speed
Replies: 27
Views: 10997

Re: Use sticks not for servo position but for servo speed

In the mixer setup there is the "Multiplex" selection with "ADD", "Multiply" and "Replace"

Select "Replace" and it will show the line with ":=" instead of "+="

Reinhard
by ReSt
Thu Jun 13, 2019 7:49 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: Use sticks not for servo position but for servo speed
Replies: 27
Views: 10997

Re: Use sticks not for servo position but for servo speed

These two mixes must be of type "Replace", not "ADD"
+= 100 Ail L02
+= -100 Ail L03

Reinhard
by ReSt
Sat Jun 01, 2019 9:33 pm
Forum: er9x
Topic: Comeback
Replies: 40
Views: 1543

Re: Comeback

Edit your er9x.hex file with a simple editor e.g. "Write" and verify the two lines I pasted in the above post.
Only to verify, if your file is the same as ours (at least at that position of the file).

Reinhard
by ReSt
Sat Jun 01, 2019 6:34 pm
Forum: er9x
Topic: Comeback
Replies: 40
Views: 1543

Re: Comeback

I would download the code again. The error message says, avrdude detected a CRC error in line 1374 of er9x.hex (the last byte in a line is the CRC check byte of the databytes of that line) 1374 is hex 55E so either the line that starts with :1055D or the next line :1055E should be the line that forc...
by ReSt
Fri May 10, 2019 12:09 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363830

Re: ERSKY9X Coding

I'm getting some compile errors for AR9x and 9XRpro with the latest download. File sTxsplash.lbm is missing (rename the s9xsplash.lbm as a fix) In the "Makefile" I had to remove line 878 ("pxx2.cpp \") (There is no pxx2.cpp file in my download). After that, it compiled without any further problems R...
by ReSt
Mon Apr 29, 2019 10:21 pm
Forum: Software
Topic: Custom Splash Screen Logo
Replies: 3
Views: 302

Re: Custom Splash Screen Logo

I think the best "grayscale like" images I got when I converted the colour image into a 16 colour scale image, from there into a grey scale image and then into black and white.

Reinhard
by ReSt
Sat Apr 27, 2019 11:02 pm
Forum: Software
Topic: Custom Splash Screen Logo
Replies: 3
Views: 302

Re: Custom Splash Screen Logo

Convert it to a bitmap and reduce the size to 128x64 pixels
And then convert it from color to black and white
gives something like this.

Reinhard
Logo.zip
(801 Bytes) Downloaded 23 times
by ReSt
Fri Mar 29, 2019 11:28 pm
Forum: Software
Topic: mix script for parachute
Replies: 17
Views: 820

Re: mix script for parachute

I checked the mixes once more and I believe they do what you want. I assume you have a working eePe / eePSky or Companion The attached file contains a parachute model for eePe and one for companion (tried it on eePe and on Companion V2.0 and V2.1) On eePe/eePSky load it with "File" - "Load model set...
by ReSt
Fri Mar 29, 2019 5:56 pm
Forum: Software
Topic: mix script for parachute
Replies: 17
Views: 820

Re: mix script for parachute

Try this, if it does what you need. This is with ER9x, so it should be poosible with all systems CH01 +100% Ail +100% Ail * +100% Ch3 // Multiply +100% Thr CH02 -100% Ail -100% Ail * +100% Ch3 + 100% Thr Ch3 +100% Thr Curve(C1) Curve c1: 100 75 50 75 100 Reinhard
by ReSt
Thu Mar 28, 2019 9:12 am
Forum: er9x
Topic: er9x on Arduino???
Replies: 2
Views: 246

Re: er9x on Arduino???

But what about a similar board with the STM32F103C8T6 that has 64k flash and 32k SRam like
https://www.ebay.de/itm/1-2-5-10PCS-STM ... DRyN79HJuQ

Reinhard
by ReSt
Wed Mar 27, 2019 8:33 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: IDLE switch for winches
Replies: 6
Views: 847

Re: IDLE switch for winches

try the following:
CH7 100% CH7
R CH7 100% HALF ID0 slow(u10:d5) // Replace mix
R CH7 -100% HALF ID2 slow(U10:d5) // Replace mix

Reinhard
by ReSt
Mon Mar 18, 2019 11:35 pm
Forum: SMARTIEPARTS PROGRAMMER
Topic: Need to fix Blank Screen on Turnigy 9X Transmitter
Replies: 24
Views: 11947

Re: Need to fix Blank Screen on Turnigy 9X Transmitter

when my two 9x (ATMEGE 128) are connected to the USBASP programmer, the displays are also blank.

Reinhard
by ReSt
Thu Mar 14, 2019 9:48 am
Forum: erskyTx (was ersky9x)
Topic: Throttle scaling/limit
Replies: 9
Views: 473

Re: Throttle scaling/limit

Add the MULTIPY mix to the e.g. throttle channel = channel 3
CH3 100% Thr
* 50% P1 Fix Offset 50 NoTrim !! Multiply

According to the position of P1 your CH3 output will be limited between 0 an 100%

Reinhard
by ReSt
Mon Mar 11, 2019 10:41 pm
Forum: Turnigy 9XR PRO radio
Topic: Turnigy 9XR Pro Hang Up intermittently.....
Replies: 34
Views: 1331

Re: Turnigy 9XR Pro Hang Up intermittently.....

My pro ran 2 1/2 hours without a problem
Display ans sound worked permanently

Reinhard

btw
Wouldn't i be an idea to power down the radio when you have Inactivity timeouts and low battery warning?
by ReSt
Mon Mar 04, 2019 8:48 am
Forum: Hardware
Topic: 9XR(AT128) bricked, HVPP unbriked and then briked again.
Replies: 78
Views: 2700

Re: 9XR(AT128) bricked, HVPP unbriked and then briked again.

0x1e9801 seams to means ATmega 2560 ????

Reinhard
by ReSt
Wed Jan 23, 2019 10:12 am
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363830

Re: ERSKY9X Coding

Can you please update Github also ?

Reinhard
by ReSt
Sun Jan 20, 2019 3:39 pm
Forum: Hardware
Topic: 9XR Pro probs
Replies: 41
Views: 1295

Re: 9XR Pro probs

does this also happen with a fresh created new model?

Reinhard
by ReSt
Thu Jan 10, 2019 8:46 am
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 1077

Re: 9XR flashing with USBASP issues!

Sometimes it helps flashing, when the cable between programmer and the processor of the radio is as short as possible.

Reinhard
by ReSt
Tue Jan 08, 2019 12:57 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 1077

Re: 9XR flashing with USBASP issues!

Searching the forum, I found suggestions of -B100 up to -B10000

Reinhard
by ReSt
Tue Jan 08, 2019 8:39 am
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 1077

Re: 9XR flashing with USBASP issues!

You may be right. and there is a difference, as you say. According to the help display from Preferences in eePe -b <baudrate> Override RS-232 baud rate -B <bitclock> Specify JTAGS/STK500v2 bit clock period (us). I don't know which one is the one to be used. I only remember that a low number was sugg...
by ReSt
Mon Jan 07, 2019 10:35 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 1077

Re: 9XR flashing with USBASP issues!

One mor possibility. Try to slow down the communication speed of AVRDude In opentx companion in settings - Configure Communications... in the "Extra Arguments" field use the parameter -b xxxxx This overrides the baudrate that is used. (if I remember correctly then the lowest value I have read of is ...
by ReSt
Mon Jan 07, 2019 7:02 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 1077

Re: 9XR flashing with USBASP issues!

There normally is a small smd resistor pack between the processor and the output pins of the board with 4 resistors (8 pins) that is marked with "101" that is 100 Ohm. These are (normally) ok. The problematic resistor packs were marked 102, that is 1kOhm, IIRC Another possibility for problems someti...
by ReSt
Fri Jan 04, 2019 10:42 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363830

Re: ERSKY9X Coding

Glad it is working and thanks for the feedback

Reinhard
by ReSt
Fri Jan 04, 2019 6:39 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363830

Re: ERSKY9X Coding

@ozphoenix I succeded to get a version of my Split program that is working on Win10. The only culprit is, you must install it (14 files totally). The zip file contains a setup.exe that you must run to install the program. The program offers a simple user interface where you can select the input file...
by ReSt
Thu Jan 03, 2019 6:25 pm
Forum: erskyTx (was ersky9x)
Topic: ERSKY9X Coding
Replies: 4455
Views: 363830

Re: ERSKY9X Coding

@ozphoenix I just have written a small program that reads a raw log file and formats it in a way like this, readable with a normal text editor 7E 98 10 01 F1 61 00 00 00 9B 7E 98 10 04 F1 59 00 00 00 A0 7E 22 10 00 02 00 00 00 00 ED 7E 16 7E E9 10 00 03 40 75 57 77 68 7E B7 7E 00 10 00 01 1E 46 00 0...
by ReSt
Tue Jan 01, 2019 12:37 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 556
Views: 72955

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

I flashed your document.eepe file onto my radio. This is what I did to get the voice running with your Eeprom setup: Power on the radio in maintenance mode, that is, power on with left horizontal trim left (and released) . You will shortly see a message of "Hardware menu enabled" In Radio setup - ha...
by ReSt
Sat Dec 29, 2018 11:44 pm
Forum: Soldering, Hardware, Skills
Topic: Desoldering The Atmega Chip Using Chip Quik
Replies: 105
Views: 19286

Re: Desoldering The Atmega Chip Using Chip Quik

But on Amazone you can find a cheaper one. Though I dont know the shipping cost. https://www.amazon.com/ChipQuik-SMD1-Leaded-Temperature-Removal/dp/B0019UZP7I/ref=pd_sim_328_4/131-1541285-4467364?_encoding=UTF8&pd_rd_i=B0019UZP7I&pd_rd_r=57976a97-0bc3-11e9-b34a-211282c114f8&pd_rd_w=IddDp&pd_rd_wg=ni...
by ReSt
Sat Dec 22, 2018 10:13 pm
Forum: openTx model setup
Topic: Control 2 servos via 1 channel for continuous rotation?
Replies: 15
Views: 829

Re: Control 2 servos via 1 channel for continuous rotation?

João, that's correct :D

And I found a solution for OpenTx also.
It works with the sticky function

ch7 = ch7 Weight(+100%)
+= ch9 Weight(+10%) Switch(!L1)
+= ch9 Weight(-10%) Switch(L1)
ch9 = Thr Weight(+50% Offset(50%)

L1 Sticky L2 L3
L2 a > x CH7 99
L3 a < x CH7 -99


Reinhard
by ReSt
Fri Dec 21, 2018 4:12 pm
Forum: openTx model setup
Topic: Control 2 servos via 1 channel for continuous rotation?
Replies: 15
Views: 829

Re: Control 2 servos via 1 channel for continuous rotation?

I found a solution with ERSky/ER9x that I believe does what you are looking for. I dont know if opentx has a similar function (Latch with set/reset). I set up a logical switch (L6) as a latch with a SET (L1) and a RESET (L2) condition. It is set, when the output channel, in my example ch07, is > 99 ...

Go to advanced search