Search found 1505 matches

by ReSt
Fri Mar 29, 2019 11:28 pm
Forum: Software
Topic: mix script for parachute
Replies: 17
Views: 598

Re: mix script for parachute

I checked the mixes once more and I believe they do what you want. I assume you have a working eePe / eePSky or Companion The attached file contains a parachute model for eePe and one for companion (tried it on eePe and on Companion V2.0 and V2.1) On eePe/eePSky load it with "File" - "Load model set...
by ReSt
Fri Mar 29, 2019 5:56 pm
Forum: Software
Topic: mix script for parachute
Replies: 17
Views: 598

Re: mix script for parachute

Try this, if it does what you need. This is with ER9x, so it should be poosible with all systems CH01 +100% Ail +100% Ail * +100% Ch3 // Multiply +100% Thr CH02 -100% Ail -100% Ail * +100% Ch3 + 100% Thr Ch3 +100% Thr Curve(C1) Curve c1: 100 75 50 75 100 Reinhard
by ReSt
Thu Mar 28, 2019 9:12 am
Forum: er9x
Topic: er9x on Arduino???
Replies: 2
Views: 155

Re: er9x on Arduino???

But what about a similar board with the STM32F103C8T6 that has 64k flash and 32k SRam like
https://www.ebay.de/itm/1-2-5-10PCS-STM ... DRyN79HJuQ

Reinhard
by ReSt
Wed Mar 27, 2019 8:33 am
Forum: er9x / gruvin9x / th9 based firmwares
Topic: IDLE switch for winches
Replies: 6
Views: 643

Re: IDLE switch for winches

try the following:
CH7 100% CH7
R CH7 100% HALF ID0 slow(u10:d5) // Replace mix
R CH7 -100% HALF ID2 slow(U10:d5) // Replace mix

Reinhard
by ReSt
Mon Mar 18, 2019 11:35 pm
Forum: SMARTIEPARTS PROGRAMMER
Topic: Need to fix Blank Screen on Turnigy 9X Transmitter
Replies: 24
Views: 11148

Re: Need to fix Blank Screen on Turnigy 9X Transmitter

when my two 9x (ATMEGE 128) are connected to the USBASP programmer, the displays are also blank.

Reinhard
by ReSt
Thu Mar 14, 2019 9:48 am
Forum: ersky9x
Topic: Throttle scaling/limit
Replies: 8
Views: 271

Re: Throttle scaling/limit

Add the MULTIPY mix to the e.g. throttle channel = channel 3
CH3 100% Thr
* 50% P1 Fix Offset 50 NoTrim !! Multiply

According to the position of P1 your CH3 output will be limited between 0 an 100%

Reinhard
by ReSt
Mon Mar 11, 2019 10:41 pm
Forum: Turnigy 9XR PRO radio
Topic: Turnigy 9XR Pro Hang Up intermittently.....
Replies: 34
Views: 971

Re: Turnigy 9XR Pro Hang Up intermittently.....

My pro ran 2 1/2 hours without a problem
Display ans sound worked permanently

Reinhard

btw
Wouldn't i be an idea to power down the radio when you have Inactivity timeouts and low battery warning?
by ReSt
Mon Mar 04, 2019 8:48 am
Forum: Hardware
Topic: 9XR(AT128) bricked, HVPP unbriked and then briked again.
Replies: 78
Views: 1821

Re: 9XR(AT128) bricked, HVPP unbriked and then briked again.

0x1e9801 seams to means ATmega 2560 ????

Reinhard
by ReSt
Wed Jan 23, 2019 10:12 am
Forum: ersky9x
Topic: ERSKY9X Coding
Replies: 4388
Views: 340614

Re: ERSKY9X Coding

Can you please update Github also ?

Reinhard
by ReSt
Sun Jan 20, 2019 3:39 pm
Forum: Hardware
Topic: 9XR Pro probs
Replies: 29
Views: 579

Re: 9XR Pro probs

does this also happen with a fresh created new model?

Reinhard
by ReSt
Thu Jan 10, 2019 8:46 am
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 834

Re: 9XR flashing with USBASP issues!

Sometimes it helps flashing, when the cable between programmer and the processor of the radio is as short as possible.

Reinhard
by ReSt
Tue Jan 08, 2019 12:57 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 834

Re: 9XR flashing with USBASP issues!

Searching the forum, I found suggestions of -B100 up to -B10000

Reinhard
by ReSt
Tue Jan 08, 2019 8:39 am
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 834

Re: 9XR flashing with USBASP issues!

You may be right. and there is a difference, as you say. According to the help display from Preferences in eePe -b <baudrate> Override RS-232 baud rate -B <bitclock> Specify JTAGS/STK500v2 bit clock period (us). I don't know which one is the one to be used. I only remember that a low number was sugg...
by ReSt
Mon Jan 07, 2019 10:35 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 834

Re: 9XR flashing with USBASP issues!

One mor possibility. Try to slow down the communication speed of AVRDude In opentx companion in settings - Configure Communications... in the "Extra Arguments" field use the parameter -b xxxxx This overrides the baudrate that is used. (if I remember correctly then the lowest value I have read of is ...
by ReSt
Mon Jan 07, 2019 7:02 pm
Forum: openTx
Topic: 9XR flashing with USBASP issues!
Replies: 23
Views: 834

Re: 9XR flashing with USBASP issues!

There normally is a small smd resistor pack between the processor and the output pins of the board with 4 resistors (8 pins) that is marked with "101" that is 100 Ohm. These are (normally) ok. The problematic resistor packs were marked 102, that is 1kOhm, IIRC Another possibility for problems someti...
by ReSt
Fri Jan 04, 2019 10:42 pm
Forum: ersky9x
Topic: ERSKY9X Coding
Replies: 4388
Views: 340614

Re: ERSKY9X Coding

Glad it is working and thanks for the feedback

Reinhard
by ReSt
Fri Jan 04, 2019 6:39 pm
Forum: ersky9x
Topic: ERSKY9X Coding
Replies: 4388
Views: 340614

Re: ERSKY9X Coding

@ozphoenix I succeded to get a version of my Split program that is working on Win10. The only culprit is, you must install it (14 files totally). The zip file contains a setup.exe that you must run to install the program. The program offers a simple user interface where you can select the input file...
by ReSt
Thu Jan 03, 2019 6:25 pm
Forum: ersky9x
Topic: ERSKY9X Coding
Replies: 4388
Views: 340614

Re: ERSKY9X Coding

@ozphoenix I just have written a small program that reads a raw log file and formats it in a way like this, readable with a normal text editor 7E 98 10 01 F1 61 00 00 00 9B 7E 98 10 04 F1 59 00 00 00 A0 7E 22 10 00 02 00 00 00 00 ED 7E 16 7E E9 10 00 03 40 75 57 77 68 7E B7 7E 00 10 00 01 1E 46 00 0...
by ReSt
Tue Jan 01, 2019 12:37 pm
Forum: er9x
Topic: ArduVoice-9x Voice Module with Arduino for the 9x Radio
Replies: 547
Views: 68162

Re: ArduVoice-9x Voice Module with Arduino for the 9x Radio

I flashed your document.eepe file onto my radio. This is what I did to get the voice running with your Eeprom setup: Power on the radio in maintenance mode, that is, power on with left horizontal trim left (and released) . You will shortly see a message of "Hardware menu enabled" In Radio setup - ha...
by ReSt
Sat Dec 29, 2018 11:44 pm
Forum: Soldering, Hardware, Skills
Topic: Desoldering The Atmega Chip Using Chip Quik
Replies: 105
Views: 18200

Re: Desoldering The Atmega Chip Using Chip Quik

But on Amazone you can find a cheaper one. Though I dont know the shipping cost. https://www.amazon.com/ChipQuik-SMD1-Leaded-Temperature-Removal/dp/B0019UZP7I/ref=pd_sim_328_4/131-1541285-4467364?_encoding=UTF8&pd_rd_i=B0019UZP7I&pd_rd_r=57976a97-0bc3-11e9-b34a-211282c114f8&pd_rd_w=IddDp&pd_rd_wg=ni...
by ReSt
Sat Dec 22, 2018 10:13 pm
Forum: openTx model setup
Topic: Control 2 servos via 1 channel for continuous rotation?
Replies: 15
Views: 610

Re: Control 2 servos via 1 channel for continuous rotation?

João, that's correct :D

And I found a solution for OpenTx also.
It works with the sticky function

ch7 = ch7 Weight(+100%)
+= ch9 Weight(+10%) Switch(!L1)
+= ch9 Weight(-10%) Switch(L1)
ch9 = Thr Weight(+50% Offset(50%)

L1 Sticky L2 L3
L2 a > x CH7 99
L3 a < x CH7 -99


Reinhard
by ReSt
Fri Dec 21, 2018 4:12 pm
Forum: openTx model setup
Topic: Control 2 servos via 1 channel for continuous rotation?
Replies: 15
Views: 610

Re: Control 2 servos via 1 channel for continuous rotation?

I found a solution with ERSky/ER9x that I believe does what you are looking for. I dont know if opentx has a similar function (Latch with set/reset). I set up a logical switch (L6) as a latch with a SET (L1) and a RESET (L2) condition. It is set, when the output channel, in my example ch07, is > 99 ...
by ReSt
Fri Nov 16, 2018 4:42 pm
Forum: The Pickled Gnu (The Pub)
Topic: Arduino Uno help
Replies: 7
Views: 3101

Re: Arduino Uno help

I found a description of how to check and how to restore the firmware of the 16U2 chip. So the code is obviously not hardcoded in this chip. https://www.instructables.com/id/How-to-Restore-the-Arduino-UNO-R3-ATmega16U2-Firmw/ And reprogramming of most of the Arduinos can be done with an USBASP progr...
by ReSt
Mon Oct 29, 2018 11:38 pm
Forum: Hardware
Topic: 9xr pro freezing up help please
Replies: 56
Views: 3750

Re: 9xr pro freezing up help please

That was the question that was answered in that post.
Does anyone have the ERC12864-2 adapter board that flygear was selling? I need one or where I can get a 30pin top to bottom ffc adapter.
I'm not sure, but I think it does.

Reinhard
by ReSt
Mon Oct 29, 2018 4:14 pm
Forum: Hardware
Topic: 9xr pro freezing up help please
Replies: 56
Views: 3750

Re: 9xr pro freezing up help please

This connector could possibly help you
https://www.rcgroups.com/forums/showpos ... count=1500

Reinhard
by ReSt
Sat Oct 13, 2018 5:04 pm
Forum: Electronic Mods
Topic: need help to repair 9X main board
Replies: 25
Views: 5708

Re: need help to repair 9X main board

on my radios EEpe reads the fuses as
extended 0xFF
High 0x81
Low 0x0E

Reinhard
by ReSt
Wed Sep 26, 2018 5:35 pm
Forum: Software
Topic: Using ER9X on Flysky 9X Tx with eePe Link software
Replies: 35
Views: 1807

Re: Using ER9X on Flysky 9X Tx with eePe Link software

As you "might" have a battery problem, did you calibrate the battery voltage? (Radio setup - diagnostic Ana - right value in the bottom line, has to be set to the voltage you measure at the battery with an instrument)

Reinhard
by ReSt
Wed Sep 26, 2018 7:48 am
Forum: er9x
Topic: FRSKY R9M compatibility?
Replies: 64
Views: 5247

Re: X7 - LDO or CPU broken

If you can read data from the radio to the PC then e.g. do a read fuses (screen will stay open so you can see what it did!)

The first step is to read the device signature (of the cpu).
0x1e9702 is M128
0x1e9602 is M64

Reinhard
by ReSt
Sun Sep 23, 2018 7:27 am
Forum: The Pickled Gnu (The Pub)
Topic: Non invert Attiny 85 led driver.
Replies: 10
Views: 1644

Re: Non invert Attiny 85 led driver.

If the posted code mod does that I’ll give it a try. That code snippet was the original code. So to have that special output (landing light) inverted the HIGH and LOW have to be exchanged with each other like in this modified code. if (state && !curLandingLight) { digitalWrite(LL_PIN_LIGHT, LOW); /...
by ReSt
Sat Sep 22, 2018 9:31 pm
Forum: The Pickled Gnu (The Pub)
Topic: Non invert Attiny 85 led driver.
Replies: 10
Views: 1644

Re: Non invert Attiny 85 led driver.

I’m trying to use a get or transistor as a led driver but it inverts the pulses. My work around was to use 2 transistors to cancel the pulse inversion. If the inversion of the signal is your only problem, why not change the code to get an inverted signal ? A short view into the mentioned code shows...

Go to advanced search