The Radioking TX18S has inbuilt charge facility - but its very slow and powered from USB C cable. In use - the rear of case gets warm so there is possibly a heat issue to note ... it is known that Jumper did not put charge into their later radios for such reason.
I would like to be cautious and not use this too often and only on low power when necessary. Therefore the 18650 holder needs to have charger suitable for it. The 18650's are LiIon at 4.2V max - so LiPo charging is fine.
The holder has the standard 2S balance plug - so if you have one of those simple 2S / 3S balance lead only chargers - that will do the job ... but again its slow.
So I decided to use my programmable LiPo chargers - but they need a main charge lead as well as balance lead ... so :
XT30 to lead ...
Poke through so contact can be made by cells pressing soldered ends of wires to contacts :
Bobs proverbial ... works a treat ...
XT30 as its small and easily sits in the battery bay ... just needed to make adaptor from XT30 to XT60 for charger ...
Modification to RK TX18S 18650 battery holder
Cant get your radio to work? General Hardware issues?
-
- Posts: 50
- Joined: Fri Aug 05, 2016 6:25 pm
- Country: -
Jump to
- OPENRC News & Information
- ↳ General Information & Rules
- ↳ Feedback
- General help and information
- ↳ Software
- ↳ Hardware
- ↳ General help (FrSky Taranis radio)
- Open Radio Control Transmitter Firmwares
- ↳ General model setup questions
- ↳ er9x / gruvin9x / th9 based firmwares
- ↳ Template Library
- ↳ Splash Screen Library
- ↳ Helicoptor Programming
- ↳ radioclone
- ↳ stock firmware (fly sky th9x)
- ↳ Template Library
- ↳ Sound Pack Library
- ↳ Edge TX
- ↳ openTx
- ↳ openTx for FrSky radios
- ↳ openTx model setup
- ↳ er9x
- ↳ er9x model setup
- ↳ ersky9xr
- ↳ erskyTx (was ersky9x)
- ↳ ersky9x model setup
- ↳ gruvin9x
- ↳ gruvin9x model setup
- ↳ th9x
- ↳ th9x model setup
- ↳ gv9x
- ↳ radioclone
- ↳ radioclone model setup
- ↳ tgy9xr
- ↳ tgy9xr model setup
- ↳ AR-T6
- ↳ other
- Desktop Software to Program Your Transmitter
- ↳ eePe
- ↳ companion9x
- ↳ eepSKYe
- Open Radio Control RF Systems & Hardware
- ↳ OpenLRS
- ↳ OpenLRSng
- ↳ OpenLRSng hardware
- Closed Source Radio Control RF Systems & Hardware
- ↳ Royal Way - Rlink UHF Long Range System
- Transmitter Hardware
- ↳ FlySky TH9X / Turnigy 9X / Eurgle 9X radio
- ↳ SMARTIEPARTS PROGRAMMER
- ↳ HARDWARE MODS & HACKS
- ↳ FRSky Telemetry Mods
- ↳ ArduPilot Mods
- ↳ Electronic Mods
- ↳ Hardware Mods
- ↳ Soldering, Hardware, Skills
- ↳ DSM2/DSMX Mods
- ↳ UPGRADE BOARDS
- ↳ sky9x upgrade board
- ↳ gruvin9x upgrade board
- ↳ 9Xtreme upgrade board
- ↳ RF MODULES
- ↳ The FRSKY Forum
- ↳ PROGRAMMERS
- ↳ FrSky Taranis radio
- ↳ FRSky Horus radio
- ↳ Turnigy 9XR PRO radio
- ↳ Orange DSM Telemetry module
- ↳ Turnigy 9XR radio
- ↳ PROGRAMMERS
- ↳ Other Radios
- ↳ Retro Radios
- Other OPEN Projects
- ↳ General RC Electronic Projects and Discussion
- ↳ OpenXVario - an open source vario supported by the open source firmwares!!
- ↳ Other Electronic Projects
- ↳ OpenFlightStab
- ↳ OpenLRSng
- ↳ 3D Printing
- Other Forums
- ↳ The Pickled Gnu (The Pub)
- ↳ FPV Projects
- ↳ Reviews
- ↳ Where to buy / Spares / Modules? Selling up?
- Links
- ↳ er9x on Google Code
- ↳ ersky9x on Github
- ↳ Gruvin9x on Google Code
- ↳ th9x on Google Code
- ↳ openTx on Google Code
- ↳ gv9x on Google Code
- ↳ radioclone on Sourceforge
- ↳ eePe on Google Code
- ↳ companion9x on Google Code
- ↳ 9X Guides
- ↳ openxvario