openrcforums

I think these speakers are not made to work with low frequencies anyway.. They just cause distortion and the premature death of the speaker.. Ask me how I know it

I didn't mean to say that you couldn't handle the 0603 I have said that is very difficult because most of the people might not be able to handle it, and if they try, they might destroy something. New radios might even be shipping with the 47K resistor but I don't know..

João

Well, yeah; but that's also a lot to do with using them "free-air".

A speaker needs a sealed enclosure to provide some back-pressure, otherwise it suffers "over-excursion"; a fancy term meaning the cone travels much further than the designers intended and things get damaged. The coil can rub against the magnet and short out, the surround and spider can rip, the cone can become distorted so the coil is no longer aligned properly. While these phenomena are most obvious with big subwoofers, the principles remain the same for small speakers and it is bad for any speaker to be used this way.


mnem
*iTuned*

Some video tutorials on how to use the new voice alarms in er9x and ersky9x
I hope they are useful

João

https://www.youtube.com/watch?v=TW9Bdrov0Ck

https://www.youtube.com/watch?v=pq3XGliAJDc

https://www.youtube.com/watch?v=6WRosEfIqC0

Well done ...

Joao:
I found in your voice pack there are two files listed as system voice files but there is no corresponding wav files. 0074 and 0075

For experts the forum:

1) I need to link the atm 6 positions of the radio channel 5 to 6 messages you.

For example, when Channel 5 is in position 956: once heard the voice "loiter"
Or, when Channel 5 is in the 1123 position, which is the voice mense "ALT HOLD".

You can program these messages? (It is to announce flight modes a drone)

thank you

Not enough information..
What is the channel values in percentage, or even microseconds (as you posted), for each of the 6 positions?
We can't guess what your controller needs if we don't use it
Also,which version of the Ersky9x firmware do you have installed on your radio?

João

OK thanks!
I try to explain better.
My team is 9XR pro-R212 with esky9x version V.4 make
I would like to set up my tx to announce voice and display each of the modes Flight my DRONE (Loiter, hold altitude, etc).
These modes are activated flights in six different parts of the ATV channel 5 on my radio ...
For example, when the ATV channel 5 is in the position .... 950 to produce a voice message and the display "loiter" .....
When channel 5 is in position atv 1145, the audio message and display says "ALTITUDE HOLD",,,, etc etc,
I appreciate any help!
thank you

petaca wrote: For example, when the ATV channel 5 is in the position .... 950 to produce a voice message and the display "loiter" .....
When channel 5 is in position atv 1145, the audio message and display says "ALTITUDE HOLD",,,, etc etc,

Well. it's the etc, etc, that we need to know. We need to know the values, otherwise we don't know what to program..


João

Thanks for the help.

The display 6/14 LIMITS ...

CHANEL 5 ATV:
1118 POSITION = "STABLE"
1323 POSITION = "loiter"
1741 POSITION = "RTL"
1404 POSITION = "ALTITUDE HOLD"
1608 POSITION = "ALTITUDE HOLD" (repeated)
2012 POSITION= "AUTO"

I want those messages onscreen and audio .....
if I could not explain it either.
thank you

Just for information, the version R212 mentioned above appears to be the new stock firmware installed at the factory for at least the last several months. It's dated February 2015.

Try this. It uses the AIL switch and the 3 position ID0/1/2 to create 6 positions.
It uses 6 logical switches. Use them in the mixer and also to create the voice events..

Thank you!!
Not even managed to enter the ATV point in the correct range for switching the 6 positions of flight (I keep trying with values and curves)

** FLIGHT MODE DISPLAY:

After setting flight modes as you suggested in the previous message may appear on the screen in large letters the six modes of flight ...?, Loiter .... ALT HOLD ... RTH ..... . AUTO STABILIZED .... .....?
  if so, as the function is set?

thank you

What flight controller do you have?
João

Thank you!
I use DEVO-M
http://www.hobbyking.com/hobbyking/stor ... _1pc_.html
thanks

Hmm, I know very little about it.. Ersky9x supports Mavlink now, and I guess it can display the different mode names on the screen. I guess yours is a different system?
If it is, I guess it is not possible.
As I said, I haven't been into multirotors for a couple years now, so I'm not updated..

João

You can name flight modes 1-6 (with 6 characters max) and these names are displayed in normal size between the Tx battery voltage and timer1 when the corresponding flight mode is active

Reinhard

True, forgot about it, thanks Reinhard.
Ok, Petaca, do the mixes I posted above work? If so, we can go from there and use flight modes..

João

ReSt wrote:You can name flight modes 1-6 (with 6 characters max) and these names are displayed in normal size between the Tx battery voltage and timer1 when the corresponding flight mode is active

Reinhard

Thank you...

Could you tell me in which messages menu on the screen are written?

thanks again

You set them up in the 'model setup' where you edit the 'Modes'
and the flight modes are displayed in the upper half in the middle of the system screens

Reinhard

jhsa wrote: Ok, Petaca, do the mixes I posted above work? If so, we can go from there and use flight modes..

João

You didn't answer this question.. I need to know this so I can help you further..

Jo~ão

I made a voice pack today geared towards what I wanted. I wanted to share it. I used Cereproc.com Voices sound fantastic! I used Heather(english,Scottland). Any way here it is I have tested it on the radio everything works that I have been able to use so far. Ok I have to shorten some file names. I got a few that are too long miscounted..



OK its back

update : Added ARMED and DISARMED voice files

Now if I could find a voice pack with a sexy British accent I'd be in heaven!

Why not create your own?

https://github.com/CaffeineAU/TTSAutomate

With this tool it is easy..
João

Is there any recent guidance on how to get the radio to work with sounds? I have seen some but they are not up to date with latest ersky9x versions. The voice package is downloaded and put in the root of the SD card

jtroutt19 wrote: ↑Sun Nov 20, 2016 1:39 am I made a voice pack today geared towards what I wanted. I wanted to share it. I used Cereproc.com Voices sound fantastic! I used Heather(english,Scottland). Any way here it is I have tested it on the radio everything works that I have been able to use so far. Ok I have to shorten some file names. I got a few that are too long miscounted..



OK its back

update : Added ARMED and DISARMED voice files

Volume is too low even at max volume.
On the timer count down, at the three minutes mark, its says four minutes.
There is no inactivity alarm file. For now its a no go, but thx for the effort.

OctavioS wrote: ↑Mon Apr 09, 2018 10:35 pm

jtroutt19 wrote: ↑Sun Nov 20, 2016 1:39 am I made a voice pack today geared towards what I wanted. I wanted to share it. I used Cereproc.com Voices sound fantastic! I used Heather(english,Scottland). Any way here it is I have tested it on the radio everything works that I have been able to use so far. Ok I have to shorten some file names. I got a few that are too long miscounted..



OK its back

update : Added ARMED and DISARMED voice files

Volume is too low even at max volume.
On the timer count down, at the three minutes mark, its says four minutes.
There is no inactivity alarm file. For now its a no go, but thx for the effort.

Here you can see and download the solution for make it Louder.
https://openrcforums.com/forum/viewtopi ... 81#p139281

I have 3 pro's and the voice files work great . The only thing I cant get to work is for it to announce the name of the model when I select it . I have put lot's of my files in the user file and they all work. When I try to display files to pick from it comes up blank.I can type in the file and it works , except on the announcing the name ..Any help ?

Thanks

Allen

There is should be 3 subfoldrers in voice folder:

system
user
modelNames

Last one you need and file name length should be no more than 8 characters(+.waw).

Directory layout for erSky9x SD card subfoldrers:
(viewtopic.php?f=35&t=9034#p116982)