Hello
My first post. Please forgive my English. I have the Eurgle,last generation 9x, and the Turborix 6 ch receiver. When I try to program v-tail for my STM Blaze, I run in to problems.I have the sender on mode two. I go to the v-tail menu. State Act. Ele 1, 050, Ele 2, 050, Rud, 050 and Rud 2 -050. No matter where I connect to the rec. I got the elevator connected to the left stick. And the rudder on the right stick. I can't fly like this, pushing the left stick to left or right to control the elevator, and pulling the right stick up and down to control the rudder. How can i program and plug the connectors so I can fly the normal way? Controlling my elevator with the right, and rudder with the left? Appreciate any help and tips.
Regards
Arne Husby
Norway
V-tail mix problems.
- Rob Thomson
- Site Admin
- Posts: 4543
- Joined: Tue Dec 27, 2011 11:34 am
- Country: United Kingdom
- Location: Albury, Guildford
- Contact:
Re: V-tail mix problems.
Hello,
Are you using the stock firmware? Or the custom firmwares like er9x/open9x?
Rob
Are you using the stock firmware? Or the custom firmwares like er9x/open9x?
Rob
Slope Soaring, FPV, and pretty much anything 'high tech'
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
...........if you think it should be in the wiki.. ask me for wiki access, then go add it!
- Crashj007
- Posts: 133
- Joined: Tue Jan 31, 2012 11:44 pm
- Country: -
- Location: Raleigh, NC, USA
- Contact:
Re: V-tail mix problems.
Sounds like you have the channels mixed up where they plug into the receiver? Sequence should match the channel order in the mixes.
--
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744
Re: V-tail mix problems.
I think he might have the stock firmware...ArneH wrote:Hello
I have the sender on mode two. I go to the v-tail menu.
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: V-tail mix problems.
Thank you for answering. Yes I have the original stock firmware on my sender. I need some advice where to plug in to the rec. And I am also interested in flashing, but need too read more first. The back-light component made for flashing I found the link to, is out of stock until end of this month.
Arne Husby
Norway
Arne Husby
Norway
Re: V-tail mix problems.
sorry I never tried the stock firmware.. dumped it imeadetly and flashed er9x..Just to make sure, did you try to swap the elevator and rudder servos on the receiver?? not sure if that would fix the problem though..
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: V-tail mix problems.
also, are the servos mounted correctly on the plane?? just checking.
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- Crashj007
- Posts: 133
- Joined: Tue Jan 31, 2012 11:44 pm
- Country: -
- Location: Raleigh, NC, USA
- Contact:
Re: V-tail mix problems.
Arne, the Smartieparts board and light are excellent and that is what I have installed. If you are in a hurry, the Hobby King LED backlight and a USB programmer mentioned on the wiki would get you started soon.
To clear up the question of which servo is which, take them out of the plane, move the sticks, and watch what they do, then put them in correctly. Or just swap the leads where plugged into the RX and see if that is correct.
To clear up the question of which servo is which, take them out of the plane, move the sticks, and watch what they do, then put them in correctly. Or just swap the leads where plugged into the RX and see if that is correct.
--
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744
FS-TH9X 2.4GHz 9CH from Nitroplanes
Smartieparts board & backlight
Stock Flysky RF and mainboard
er9x FW V 744
Re: V-tail mix problems.
The servos are ready mounted from the producer of the model. I have tried many times to swap the connectors too. I think I will take the servos out, and flashing is the next step.