have no ppm slot or choice in the control radio set up
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
have no ppm slot or choice in the control radio set up
my er9x firmware is not showing the whole or all the choices in the control section I'm missing the ppm option how or what did I do wrong what do I need to do re flashed twice AND STILL SAME ISSUE does anyone no why please help need to get back up in the air
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: have no ppm slot or choice in the control radio set up
Sounds unusual! The PPM settings are in the model setup, under "protocol". Is this where you are looking?
Also what revision of er9x are you using (the number on the "Version menu" beside "SVN:")?
Mike.
Also what revision of er9x are you using (the number on the "Version menu" beside "SVN:")?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: have no ppm slot or choice in the control radio set up
OK Im using the v218 I having trouble getting my turnigy 9 ch receiver to bind with the transmitter its not binding only if I go back to the original 9x it binds fast its not working when I install back the 9xtreme board and also the numbers on the screen are not showing like on the youtube shows 1/11 2/11 3/11 and so on no page numbers
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
how to use the scandisk recordings
how do I use the voice recordings from the scan disk if the er9x version 218 don't have any way to pull the recordings out there is no selection on any of the screens it shows the scan disk is there and active but it does not have any selection to open for a voice recording
Re: RE: Re: have no ppm slot or choice in the control radio set up
The RF module binding with the receiver has nothing to do with the radio itself.. Do you have servos connected to the receiver?silversurfer48 wrote:OK Im using the v218 I having trouble getting my turnigy 9 ch receiver to bind with the transmitter its not binding only if I go back to the original 9x it binds fast its not working when I install back the 9xtreme board and also the numbers on the screen are not showing like on the youtube shows 1/11 2/11 3/11 and so on no page numbers
Also go to the main screen that shows some bars that represent the channels. Do the bars move when you move the sticks?
There are no more numbered pages in ersky9x. The videos you are watching are probably quite old.
Press the menu key long to open a popup menu that will allow you to select radio setup or model setup. Selecting for example model setup will take you to an index menu that lists all the menus. Select the one you need to edit.
All is organised now. And much easier to find..
João
EDIT: And please use punctuation when you write. A "." Is not so hard to type at the end of each sentence. That makes it easier for us to understand what you mean..
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: RE: how to use the scandisk recordings
Ok, I assume that by "Scan Disk" you mean "SD Card", right?silversurfer48 wrote:how do I use the voice recordings from the scan disk if the er9x version 218 don't have any way to pull the recordings out there is no selection on any of the screens it shows the scan disk is there and active but it does not have any selection to open for a voice recording
I can see you are not familiar with ersky9x. Do like this:
Go to www.er9x.com and download the "er9x manual"
Er9x is a light version of ersky9x but the basics are the same. Some options will be missing but the basic programming is the same and you will learn what the different options mean and what they do.
There is also a voice chapter that shows how to program voice events.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: is this the way the er9x is
no page numbers Im looking for page numbers like in all the youtub
Re: have no ppm slot or choice in the control radio set up
You won't find any more ersky9x firmware with page numbers, sorry..
As I said, those youtube videos might be too old.. There is openTX that still use page numbers as far as I know, but it doesn't support the 9xtreme board yet..
Please have a look at the manual to learn how to program your radio.
viewtopic.php?f=5&t=6473
Also, if you like videos, here is a Playlist with some I have made. There are a couple about voice programming.
https://www.youtube.com/playlist?list=P ... qcuIqJXhb9
João
As I said, those youtube videos might be too old.. There is openTX that still use page numbers as far as I know, but it doesn't support the 9xtreme board yet..
Please have a look at the manual to learn how to program your radio.
viewtopic.php?f=5&t=6473
Also, if you like videos, here is a Playlist with some I have made. There are a couple about voice programming.
https://www.youtube.com/playlist?list=P ... qcuIqJXhb9
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Help getting the volume to work
I'm trying to get the voice to work on the TX its not working for me i have followed all the instruction on the er9x manual no progress Help!
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: have no ppm slot or choice in the control radio set up
Do you have any beeps (e.g. when pressing keys) or voice output at all (e.g. a welcome message)?
Please also give a specific example of what you have tried and what you expect to happen.
Mike.
Please also give a specific example of what you have tried and what you expect to happen.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
ppm issue
Should TX protocol switch both be on? Because it looks has if this is the only way it looks if its binding but don't have proper settings for the RX quadcopter to test if its bind. I used the templete that was on one of rc openforums page. But dont know if its right with my 250 eachine racer can you please help me out with my problem
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: have no ppm slot or choice in the control radio set up
Are these "TX protocol switch" on the Tx module, if so what module is it?
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: have no ppm slot or choice in the control radio set up
its RF9XV2 Turnigy native 2.4 ghz
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re:no sound no sound
I have no beeps and no sound. I have check speaker and it is connected right . I have smartie board extreme installed. I'm thinking maybe the scan disk is not properly loaded with voice but then still I'm not getting any beeps.
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
have no ppm slot or choice in the control radio set up
Please tell us exactly what equipment you have. If it's the stock Turnigy module, there are no switches on the module. So I'm guessing you are talking about Protocol in Model Settings in ErSky9x.
The FlySky/Turnigy module works with default settings.
The FlySky/Turnigy module works with default settings.
Re: Re:no sound no sound
Please go to Radio setup menu, AudioHaptic menu.. What setting you have selected in "Beeper"?silversurfer48 wrote:I have no beeps and no sound. I have check speaker and it is connected right . I have smartie board extreme installed. I'm thinking maybe the scan disk is not properly loaded with voice but then still I'm not getting any beeps.
Also make sure the volume setting is not zero..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: have no ppm slot or choice in the control radio set up
To avoid confusion, SD in this context stands for Secure Digital and has nothing to do with Scan Disk, which is a Microsoft program.
The SD card is always called the SD card.
The SD card is always called the SD card.
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: have no ppm slot or choice in the control radio set up
I have did all that setting and still no beep or no voice and the sd does show active I open the tx and the speaker is connected Im not able to use eepe the only one thats allowing me to flash is skyeepe so I dont know if that has anything to do with that
- MikeB
- 9x Developer
- Posts: 17995
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: have no ppm slot or choice in the control radio set up
I'm deducing the following.
1. You have a 9X radio fitted with a 9Xtreme upgrade board.
2. You have used eepskye to update the firmware on the 9Xtreme to revision 218.
Voice messages come from the SD card.
Beeps are generated directly, so should work even if the SD card is not working.
Please report what values you have in the "AudioHaptic" menu for:
1. Volume
2. Beeper.
For Volume I would like to see a value of 7 or greater.
For Beeper I would like to see "Norm".
Mike.
1. You have a 9X radio fitted with a 9Xtreme upgrade board.
2. You have used eepskye to update the firmware on the 9Xtreme to revision 218.
Voice messages come from the SD card.
Beeps are generated directly, so should work even if the SD card is not working.
Please report what values you have in the "AudioHaptic" menu for:
1. Volume
2. Beeper.
For Volume I would like to see a value of 7 or greater.
For Beeper I would like to see "Norm".
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: have no ppm slot or choice in the control radio set up
Yeah, I already asked that before but no valid answer..
silversurfer48, you must answer our questions or we are not able to help you. Remember that we can't see your radio, so you must tell us what settings you have..
João
silversurfer48, you must answer our questions or we are not able to help you. Remember that we can't see your radio, so you must tell us what settings you have..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- silversurfer48
- Posts: 88
- Joined: Fri Feb 26, 2016 7:00 am
- Country: United States
- Location: Los Angelas Ca
- Contact:
Re: have no ppm slot or choice in the control radio set up
Ok guys you got me on the right track thank you for your help