Taranis x7 wont bind
Taranis x7 wont bind
I got the new taranis x7.I flash with companion 2.2 for the german menu.
The flash runs without a problem.But after flash i got a warning somesthing wrong with the sd card.(picture)
I try a serveral firmwares on rx and for the internal modul.Can´t fix it to bind.
Can someone suggest me a firmware for both that works?
I got a X6R and some X8R Reciever.
Greetings Markus
-
- Posts: 750
- Joined: Tue Dec 27, 2011 11:22 pm
- Country: United States
- Location: Carson City, Nv
Re: Taranis x7 wont bind
The card warning ia just the version of the sounds file does not match what the system expects. The mostly likely symptom is something like Altitude being announced as degrees instead of feet or meters. Also some scripts such S6R can have updated functions.
Down load the correct SD to go with release 2.2, copy it to the SD and the warning will go away.
The file opentx.sdcard.version on the SD is all that gets checked to produce that warning message.
BUT ,,,,, It has absolutely no relation to binding.
Binding can work fine with no SD installed in the transmitter.
The bind issue is most likely to be that either receivers (transmitter) is the EU/LBT version and the transmitter (or receivers) item is FCC version.
That should only happen if you bought and transmitter from one source then bought the receivers from a source from a different company or another country.
Down load the correct SD to go with release 2.2, copy it to the SD and the warning will go away.
The file opentx.sdcard.version on the SD is all that gets checked to produce that warning message.
BUT ,,,,, It has absolutely no relation to binding.
Binding can work fine with no SD installed in the transmitter.
The bind issue is most likely to be that either receivers (transmitter) is the EU/LBT version and the transmitter (or receivers) item is FCC version.
That should only happen if you bought and transmitter from one source then bought the receivers from a source from a different company or another country.
Dean
OldDmbThms: 1. Takeoff, 2. Crash, 3. Repair, GOTO 1
OldDmbThms: 1. Takeoff, 2. Crash, 3. Repair, GOTO 1
Re: Taranis x7 wont bind
I got it running!
I flasht on the internal XJT and on the receiver the stock EU Firmware.And then it works.
One Question now,the telemetry show me only the hole voltage of the fly batterie and not the singel cell voltage.
Is this normal?My old 9XR was abel to show it.
Thanks for help so far...
Greetings Markus
I flasht on the internal XJT and on the receiver the stock EU Firmware.And then it works.
One Question now,the telemetry show me only the hole voltage of the fly batterie and not the singel cell voltage.
Is this normal?My old 9XR was abel to show it.
Thanks for help so far...
Greetings Markus
-
- Posts: 750
- Joined: Tue Dec 27, 2011 11:22 pm
- Country: United States
- Location: Carson City, Nv
Re: Taranis x7 wont bind
What sensor for voltage. If you were previously using 2.0.xx you may not realize you have to set telemetry 'calculated' telemetry to get the indiviual cells.
Dean
OldDmbThms: 1. Takeoff, 2. Crash, 3. Repair, GOTO 1
OldDmbThms: 1. Takeoff, 2. Crash, 3. Repair, GOTO 1
Re: Taranis x7 wont bind
Thanks for advise,now it was showing!And one last thing.
How do I get there that make an announcement at a given value?
For the flaps Position i make it on the switches.
How do I get there that make an announcement at a given value?
For the flaps Position i make it on the switches.
Re: Taranis x7 wont bind
Alright,i got it found out.Everthing is fine now!