Need some help here guys,Is my first Drone build.
How are you guys resetting the Throttle Warning after going from mode 1 to mode 2?
I performed the parts swap from right to left gimbals then did the firmware upgrade to r220.C
I'm using the Simple 4 Channel Template.
What is that I'm doing wrong
Thanks....
Turnigy 9xr pro from mode 1 to mode 2
Re: Turnigy 9xr pro from mode 1 to mode 2
You will have to tell the firmware that you've changed to mode 2.
Radio Setup/Controls then last line.
João
Radio Setup/Controls then last line.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Turnigy 9xr pro from mode 1 to mode 2
Under Control Channel Order is set to RTEA, Cross Trim and Throttle Reverse are not selected. Mode 2 is Set to Rud,Thr,Ele,Ail. Does the SD card need to be IN when Doing Flash process? My SD card is not good...
Modes
F0 ---- RETA
F1 to F6 ---- ---- 0000
No idea if this helps.
Thanks for the respond...
Modes
F0 ---- RETA
F1 to F6 ---- ---- 0000
No idea if this helps.
Thanks for the respond...
Re: Turnigy 9xr pro from mode 1 to mode 2
Found a different way of doing the swap..Put it back to Mode 1.
What I did instead was swap the potentiometers from Right to Left to eliminate the issue with the short wire.Now the trick is swap the wire at the potentiometers leaving the middle wire alone just swap the end wires at the plug,the best way is having magnifying goggles and a small screwdriver to lift the little plastic that holds the wire then pull it a swap it and that's it...Warning be gentle with the potentiometers when removing them they are cheap....Now I'm on my way to work later I try to load a video...Peace .. Thanks
What I did instead was swap the potentiometers from Right to Left to eliminate the issue with the short wire.Now the trick is swap the wire at the potentiometers leaving the middle wire alone just swap the end wires at the plug,the best way is having magnifying goggles and a small screwdriver to lift the little plastic that holds the wire then pull it a swap it and that's it...Warning be gentle with the potentiometers when removing them they are cheap....Now I'm on my way to work later I try to load a video...Peace .. Thanks
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9xr pro from mode 1 to mode 2
It is a lot easier to make the change in the firmware.
viewtopic.php?f=5&t=6473).
(Note: Being created is an ErSky9x Manual, it is not ready for release yet.)
Also you can see the 9XR-Pro Manuals for erSky9x: (viewtopic.php?f=122&t=5575#p79483).
Er9x/Ersky9x Video Tutorials here: (https://www.youtube.com/playlist?list=P ... qcuIqJXhb9).
Bob B.
Download er9x manual found here: ((Note: Being created is an ErSky9x Manual, it is not ready for release yet.)
Also you can see the 9XR-Pro Manuals for erSky9x: (viewtopic.php?f=122&t=5575#p79483).
Er9x/Ersky9x Video Tutorials here: (https://www.youtube.com/playlist?list=P ... qcuIqJXhb9).
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Turnigy 9xr pro from mode1 to mode2
Thanks For All the Info...
Actually it was much easier to swap the gimbals and the potentiometers to resolve the issue with the wire been to short.
Actually it was much easier to swap the gimbals and the potentiometers to resolve the issue with the wire been to short.