Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
I have a Turnigy 9XR Pro running ersky9x-pr219, Version V.490-Mike. I have inserted a Frsky XJT Model (Which has a 2015 label on it). I have purchased two receivers that have the X8R_150115 firmware now installed (Someone suggested the firmware on the receiver was the issue). I am unable to bind in Mode 5 (D16). When I press the F/S button and add the power to the receiver I just get both a solid green and red LED.
I have managed to bind one of the two receivers in D8 with the jumper across channel 7&8, but this will not bind in D16 regardless of EU or Non EU firmware.
Any help gratefully received as I'm running out of ideas....
I have managed to bind one of the two receivers in D8 with the jumper across channel 7&8, but this will not bind in D16 regardless of EU or Non EU firmware.
Any help gratefully received as I'm running out of ideas....
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
You did not mention your module settings on the radio. When using PXX you need to use the menu commands to bind, NOT the button.
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Both dip switches are down (off) on the XJT Module.
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
In the Protocol Screen:
PPM2 not selected
Module selected
Proto PXX RXNum 1
Type D16
Chans 8
Country Ame
1st Chan 1
Bind (I've been using this rather than pressing the Module button)
PPM2 not selected
Module selected
Proto PXX RXNum 1
Type D16
Chans 8
Country Ame
1st Chan 1
Bind (I've been using this rather than pressing the Module button)
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Fixed it! I upgraded the XJT Module to XJT_141016.frk and both receivers have bound in D16.
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
I have been trying to get my telemetry to work. I downloaded the new ersky9x-pr219 V.841-Mike. I have been trying to update the xjt_141016 but when it choose to update the s port on the turnigy the bar doesnt move. I will let it sit for a while but nothing. Help Please.
x4r-sb
XJT
Kiss FC
x4r-sb
XJT
Kiss FC
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
1. When, and where, did you purchase the XJT?
2. Can you bind to a receiver OK?
Mike.
2. Can you bind to a receiver OK?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Bought the xjt from ready made rc. Got it about a month ago
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
yes It binds fine
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
If it binds OK, then telemetry should be OK.
Check your settings in the Telemetry menu:
Usr Proto = Frsky
FrSky Com port = 1
Invert COM1 is not ticked
and in the protocol menu you are using PXX as the protocol.
Mike.
Check your settings in the Telemetry menu:
Usr Proto = Frsky
FrSky Com port = 1
Invert COM1 is not ticked
and in the protocol menu you are using PXX as the protocol.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
HOLY MOSES. THANKS!!!
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
OK Mike (or anyone), got another one for you. With the telemetry working and I can see voltage of the flight battery, How do I get the lowest cell to show? I want to set up a low voltage alarm so I know when to bring her in. Thanks
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Do you actually have a cell sensor?
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
I assumed it would tell me with the telemetry I have. I guess I will have to run alarm based off the full battery pack then.
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
It can't guess the cell voltages if nothing is connected to the balance port to measure them...
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
What telemetry sensors do you have?
How is the flight pack voltage being connected?
Mike.
How is the flight pack voltage being connected?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
x4r-sb, xjt, kiss fc
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
So it seems the FC is sending the flight pack voltage (I don't know anything about this FC). Do you have a connection from the Fc to the balance port of the flight battery? If not, then there is no way the FC can return individual cell voltages.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
ok gotcha. thanks mike
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
I think it uses the FrSky Battery Voltage Sensor (FBVS-01): http://flyduino.net/ultraesc/downloads/ ... .01-en.pdf
More info here: http://www.rcgroups.com/forums/showthread.php?t=2555204
Bob B.
More info here: http://www.rcgroups.com/forums/showthread.php?t=2555204
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
No, the FC measures the total battery voltage itself and reports it as VFAS on the smart port.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Turnigy 9xr pro, Frsky XJT & X8R receiver binding issues
Bob B.Kilrah wrote:No, the FC measures the total battery voltage itself and reports it as VFAS on the smart port.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).