Turnigy 9xr Pro telemetry issues PLEASE HELP

Cant get your radio to work? General Hardware issues?
Post Reply
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

I am Having trouble setting up telemetry (just battery voltage) on my 9XR pro. I have the Frsky DJT, Frsky D4R-II, Frsky battery voltage sensor, and the Frsky telemetry & headtrack extent cable for 9XR Pro. On the 9XR pro I get TX and RX readings but no voltage or anything else. I did the update from 212 to 218What am I doing wrong?

settings:

UsrProto: FrHub
RSSI Warn: 45 ON
RSSI Critical: 42 ON
Rx Voltage: 13.2v
BT Telemetry: OFF
FrSky Com Port: 2
COM2 Funct.: Telemetry
COM2 Baudrate: 57000

Thanks

User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by MikeB »

Have you set the A1 range in the telemetry menu?

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

The only thing I have set was the settings that you see up top. What range would I have to set the A1? I'm still learning

Thanks
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by jhsa »

That depends on the sensor you have. I can see you did set "RX Voltage" at 13.2V, so you might have a 4:1 voltage divider ratio sensor.. Set A1 to the same 13.2V value, and check with a voltmeter it reads correctly. You can adjust the value to read the same as your voltmeter..

João

EDIT: you might have to actually A2 instead of A1, as the D4R-II reads the receiver own voltage on A2, and it doesn't have a A1 port..
another question, how did you connect the sensor to the D4R-II receriver?
And exactly which frsky sensor you have?

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

I have the frsky voltage sensor connected to the (white wire) frsky d4r-ii side port (AD2) and the other end of the sensor to the power board. I will try what you said when I get home from work later on today.

vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

the voltage sensor is the frsky FBVS01
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by jhsa »

If you have the sensor connected to A2 on the receiver, then you have to configure A2 on the radio.. :)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

How do I configure A2?
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by jhsa »

Model Setup/Telemetry menu..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by MikeB »

It is on the telemetry menu. Go down to:
A2 channel
and where it shows 0.00v, change the 0.00 to 13.2. This assumes the FBVS is set for a ratio of 4:1.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

I'm using a 1300 3s battery. Does that make a difference?
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

it says 11.2 v on the battery but fully charged it reads on my 12.6v on my multimeter
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

BTW the ratio is 6:1 on the sensor
User avatar
bob195558
Posts: 2377
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by bob195558 »

For User Manuals for now use the Er9x Manual find it here: (viewtopic.php?f=5&t=6473).
(Note: Being created is an ErSky9x Manual, it is not ready for release yet.)
Also you can see the 9XR-Pro Manuals for erSky9x: (viewtopic.php?f=122&t=5575#p79483).
Er9x/Ersky9x Video Tutorials: (https://www.youtube.com/playlist?list=P ... qcuIqJXhb9).
I do not think there is a video for setting the Telemetry yet.

Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

Thanks you... That helps a lot
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

Thank all of you. You guys are amazing.
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

Now if I can only get the 9xr pro to tell my what flight mode I'm in
vegafoxx
Posts: 28
Joined: Sun Apr 03, 2016 1:20 am
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vegafoxx »

NVM got it. lol
vwvr6
Posts: 1
Joined: Thu Jun 23, 2016 12:53 pm
Country: -

Re: Turnigy 9xr Pro telemetry issues PLEASE HELP

Post by vwvr6 »

Hi vegafoxx, I just got my 9xr pro, and will be buying the Frsky DJT, Frsky D4R-II, being a newbe, would love to have a quick steps guide from your 9XR pro setup and the D4R+sensor connection to get the telemetry working. Or if there is already a quick source of reference that will be much appreciated.
Cheers
David.

Post Reply

Return to “Hardware”