I have to go back to my stock board in my 9x and currently have M9 gimbals installed.
I can't use them with the stock board because it's 5v. I want to put 5v hall sensors in the M9s so I can keep using them. Even if the resolution isn't actually going to be better (8bit adc in the oem 9x board), they are better build quality and ball bearing.
I am novice, but from what I can find, I need a 5v tolerant linear hall effect sensor. I don't know what I'm looking for exactly, but I found these as well as several others.
Thoughts?
Convert M9's to 5v hall sensors
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Convert M9's to 5v hall sensors
You'd be better off adding a 3V regulator to power the gimbals as they are.
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Convert M9's to 5v hall sensors
It would, but changing the sensors would likely bring a load more problems.
Those that are in place are said to be calibrated after installation to ensure linearity.
Those that are in place are said to be calibrated after installation to ensure linearity.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Convert M9's to 5v hall sensors
Upgrade to the AR9x Upgrade Board would solve your troubles.
The AR9x Upgrade Board powers the Gimbals with the proper M9 needed voltage.
Find for the 9X, AR9x Upgrade Board here: (http://www.ar9x.net/).
This will move you from using er9x firmware to erSky9x firmware making your Radio a lot more powerful.
Bob B.
The AR9x Upgrade Board powers the Gimbals with the proper M9 needed voltage.
Find for the 9X, AR9x Upgrade Board here: (http://www.ar9x.net/).
This will move you from using er9x firmware to erSky9x firmware making your Radio a lot more powerful.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Convert M9's to 5v hall sensors
YES! That's a great idea, except that I already have one but it has an issue and I can't trust it to fly dangerous or expensive planes/helis.bob195558 wrote: ↑Sun Sep 17, 2017 12:44 am Upgrade to the AR9x Upgrade Board would solve your troubles.
The AR9x Upgrade Board powers the Gimbals with the proper M9 needed voltage.
Find for the 9X, AR9x Upgrade Board here: (http://www.ar9x.net/).
This will move you from using er9x firmware to erSky9x firmware making your Radio a lot more powerful.
Bob B.
Since there are no more AR9x's available (I've contacted Jetflyer already) I am going to go back to the stock board.
I can either sell the M9s, or make them work with stock board.
I think I'm going to roll the dice and try to install 5v hall effect sensors. I know kilrah had mentioned that they were calibrated at the factory, but from the conversions I have seen the hard part is usually aligning the magnet correctly. Since I'm just swapping the sensor, the magnet should be aligned within an acceptable variation.
Input is still welcome
Re: Convert M9's to 5v hall sensors
They will only be calibrated with the new sensors if the sensors have exactly the same specs (mV/G) as the original but for 5V, they must be placed exactly in the same spot and height as the original ones, and obviously they must be pin compatible..
I did replace the pots on one of my 9x radios with hall sensors. It wasn't an easy task.
João
Sent from my thor using Tapatalk
I did replace the pots on one of my 9x radios with hall sensors. It wasn't an easy task.
João
Sent from my thor using Tapatalk
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Convert M9's to 5v hall sensors
I think I'm going to make new PCBs and set the original boards off to the side, just in case I need to go back (Like if my conversion fails miserably, or I get the AR9x working reliably)