Hello everybody
I own a Taranis, not the plus one.
I'll like to control the volume of the messages not only for the selected model, but also for the wellcome message and preflight alarms.
Is it possibole with OpenTX 2.1.6??
I set a global function (GF1) like this
But it only works after the completion of preflight switch/sticks check.
The tada and preflight alarm are played at the volume set in the general settings for the radio..
Is there any way to do it?
Thanks
Pietro
Taranis - Regulate general volume by S1
Re: Taranis - Regulate general volume by S1
No not at this point.
Re: Taranis - Regulate general volume by S1
Ok, thanks!
It would be nice, otherwise I wake up my parents in the night if I don't take care of the volumes
Bye
It would be nice, otherwise I wake up my parents in the night if I don't take care of the volumes
Bye
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Taranis - Regulate general volume by S1
HI pieri70,
erSky9x on Taranis, I believe, can do what you want.
I do not remember how it is activated, but it is something like holding one of
the horizontal trim switches to one side when powering up your radio.
This mutes all voices when booting up.
Bob B.
erSky9x on Taranis, I believe, can do what you want.
I do not remember how it is activated, but it is something like holding one of
the horizontal trim switches to one side when powering up your radio.
This mutes all voices when booting up.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: Taranis - Regulate general volume by S1
Bob, I think you mean hold both menu and exit keys at power up. That will mute all sounds.
Ersky9x does remember last volume setting I believe, but pieri70 asked about openTX on Taranis
João
Ersky9x does remember last volume setting I believe, but pieri70 asked about openTX on Taranis
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Taranis - Regulate general volume by S1
Ersky9x (including on the Taranis) does load the current model before the "welcome" message and if a pot is assigned to the volume it does use that pot setting for the volume.
As it happens, ersky9x on the Taranis doesn't (didn't!) support the mute at power up, just added it to the source code.
Mike.
As it happens, ersky9x on the Taranis doesn't (didn't!) support the mute at power up, just added it to the source code.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Taranis - Regulate general volume by S1
So, I wasn't completely wrong then
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: Taranis - Regulate general volume by S1
Super thanks!
Inviato dal mio SM-N9005 utilizzando Tapatalk
Inviato dal mio SM-N9005 utilizzando Tapatalk