Page 1 of 1
ON OFF switch using the SH switch at the Taranis
Posted: Sun Aug 31, 2014 5:41 pm
by norwenkel
Dear all,
I'm looking for a way to program a ON OFF SWITCH in my model using the SH switch at the Taranis TX. Meaning pressing SH once e.g. the data logging should start and pressing the SH again the looking should stop. If anybody is out here and have a solution please replay on this.
Kind regards
Norbert
Gesendet von meinem iPad mit Tapatalk
Re: ON OFF switch using the SH switch at the Taranis
Posted: Sun Aug 31, 2014 6:06 pm
by Carbo
You can switch a GVAR between 0 and 1, if it is 0 AND SH (logical switch (LS), increase it, if it is 1 AND SH (LS) decrease it with a special function. LS for testing the GVAR and a special function checking this LS for logging.
Re: ON OFF switch using the SH switch at the Taranis
Posted: Sun Aug 31, 2014 6:19 pm
by norwenkel
Thanks Carbo, that sounds like a good way to proceed. I will try to find a way to put your ideas in a program code. Maybe you already have done it?
Kind regards
Norbert
Gesendet von meinem iPad mit Tapatalk
Re: ON OFF switch using the SH switch at the Taranis
Posted: Sun Aug 31, 2014 6:25 pm
by Helle
Hy Norbert
mutch simpler
think you have opentx V2.08 german installed
use a Log switch and SRFF, its a Set Reset FlipFlop (sticky)
if V1 and V2 is same switch, here SHv, then you have a Toggle FlipFlop
L1 SRFF SHv SHv
then at Spezial Funktion Start Data Logging with the L1
SF1 L1 Start Log 0,1s
-------------------------
Much more examples at the Opentx German Manual (about 290pages) ..... _1608_028.pdf
viewtopic.php?f=92&t=3563&p=85090&hilit ... ual#p85090
Helle
Re: ON OFF switch using the SH switch at the Taranis
Posted: Mon Sep 01, 2014 6:48 am
by norwenkel
Perfect Helle,
thats solve my request very well. Thanks for informing me about the 0.28 vers. of the german manual.
Take care
Norbert
Re: ON OFF switch using the SH switch at the Taranis
Posted: Sat Sep 06, 2014 6:57 am
by Jamukah
Hi Norbert,
it is also possible to start / stop logging by the GAS stick. I Prefer this setting. But this makes only sense as long you programming this function for a non -slider modell
For this case, my settings for SF and LS:
BR
Oliver
Re: ON OFF switch using the SH switch at the Taranis
Posted: Tue Sep 09, 2014 9:28 pm
by utmanaren2002
Hi guys
I have upgraded to 2.08 and can't find toggle mode as before. I used SH for throttle hold with a t to get SH toggled but now I can't find the t anymore?
Has it gone in 2.08?
Please answer if you can help me to fix it in another way
Skickas från min iPad via Tapatalk
Re: ON OFF switch using the SH switch at the Taranis
Posted: Wed Sep 10, 2014 11:04 am
by Kilrah
See the posts above yours. A logic switch with Sticky SHdown SHdown is what you want.
Re: ON OFF switch using the SH switch at the Taranis
Posted: Sun Nov 27, 2016 10:12 pm
by Deadtillten
I have assigned my sticky switch the led's to on and off. If anyone know's how to put audio," led's on " and then " led's off " to the switch ? Would they be kind enough to post please. I've tried lots of combinations and I always get " led's on " and " led's on".
It would be very much appreciated.
Re: ON OFF switch using the SH switch at the Taranis
Posted: Mon May 01, 2017 9:50 am
by Deadtillten
It looks like sticky switch can't be assigned any on/off audio or am I just thick. (don't answer that, lol)
Re: ON OFF switch using the SH switch at the Taranis
Posted: Mon May 01, 2017 11:47 am
by jtaylor
Assuming L1 is your sticky
L1 SH↓ SH↓
Use two SF's for the audio
SF1 L1 Play Tarck ledon.wav "play once - not during startup"
SF2 !L1 Play Track ledoff.wav play once - not during startup
Jim