error flashing internal xjt via taranis tx on opentx 2.1.7
error flashing internal xjt via taranis tx on opentx 2.1.7
When I try to flash firmware to taranis plus internal xjt rf I get an error. It comes up with a bar and says writing. Nothing happens for 2 or 3 seconds, then it comes up error. I am unable to bind my x series rx to the tx. Any ideas what to do to rectify this problem?
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: error flashing internal xjt via taranis tx on opentx 2.1.7
Hi timbo69,
I do not use opentx 2.1.7 and so I am not able to help.
But I believe if you use the radio firmware erSky9x on Taranis it will work (http://www.er9x.com/).
(http://frsky-rc.com/download/view.php?s ... rmware-XJT)
(http://frsky-rc.com/download/view.php?s ... re-X8R/X6R)
Bob B.
I do not use opentx 2.1.7 and so I am not able to help.
But I believe if you use the radio firmware erSky9x on Taranis it will work (http://www.er9x.com/).
(http://frsky-rc.com/download/view.php?s ... rmware-XJT)
(http://frsky-rc.com/download/view.php?s ... re-X8R/X6R)
Bob B.
Last edited by bob195558 on Wed Feb 10, 2016 12:21 pm, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: error flashing internal xjt via taranis tx on opentx 2.1.7
When did you purchase your Taranis plus, and was it purchased within the EU?
I've seen some reports that recent EU units may have a lock on the internal XJT (with the latest EU LBT firmware) that prevents them from being flashed with older (and non-EU) firmware.
If this is the case, it is because FrSky are already complying with a regulatory requirement that is required later this year.
Mike.
I've seen some reports that recent EU units may have a lock on the internal XJT (with the latest EU LBT firmware) that prevents them from being flashed with older (and non-EU) firmware.
If this is the case, it is because FrSky are already complying with a regulatory requirement that is required later this year.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: error flashing internal xjt via taranis tx on opentx 2.1.7
How can I tell if the internal xjt is working? Is there any way of knowing if it transmitting a rf signal? I think that my internal xjt isn't working. Am I able to buy just the rf board by itself?
Re: error flashing internal xjt via taranis tx on opentx 2.1.7
No way to know for sure without specific test equipment if you can't get a receiver to work.
You can buy the back board yes.
You can buy the back board yes.
Re: error flashing internal xjt via taranis tx on opentx 2.1.7
Got a new backboard in the mail today. Took two attempts to get the aerial soldered right. Works perfect now. Flashed the firmware no problems. Is there anywhere i can send the defective board to get looked at to see if it can be repaired?