how may I change the default switch position to be -100 low on a taranis x7?
I am setting up Taranis to fly spektrum SAFE BNF models following the guide emulating a DX5e the inputs on the document states
Inputs
Rud 70 Rud E20 SG low
85 Rud E20 SG- Mid
100 Rud E20 --- Hi
The problem is the default position of the 3 position switch starts out in mode 3 which is +100.
I would like to know how to change the default of the switch to -100 low
Cheers
Crunch
how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
Re: how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
I'm a little confused by your question. There is no default when a switch is used as a switch (as opposed to a source).
When used as a source SG↑ (up) is -100, SG- (Mid) is 0 and SG↓ (down) is 100. When used as a switch you use SG↑ SG- or SG↓ . In your case where you have 70 Rud E20 SG you would use either SG ↑ or SG↓ depending on which way you want.
Jim
When used as a source SG↑ (up) is -100, SG- (Mid) is 0 and SG↓ (down) is 100. When used as a switch you use SG↑ SG- or SG↓ . In your case where you have 70 Rud E20 SG you would use either SG ↑ or SG↓ depending on which way you want.
Jim
Re: how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
Jim
Thanq that was the info I was looking for. I wish there was a complete document that went over all the programing info and sample programs and mixes
Cheers
Crunch
Thanq that was the info I was looking for. I wish there was a complete document that went over all the programing info and sample programs and mixes
Cheers
Crunch
Re: how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
The documentation that thebrairs0 did is the best I have seen. It is for openTX 2.1 but most applies to 2.2 viewtopic.php?f=45&t=8724
Jim
Jim
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
Just be sure to set all channel limits to 80% when dealing with a model intended for use with a Spektrum transmitter.
In OpenTX, 100% travel is equivalent to 125% in a Spektrum transmitter. Not only will the servos overtravel if the Taranis is set to 100% limits, but in some cases the SAFE system reacts badly to the increased pulse width. Also, the ESC is expecting to see Spektrum limits.
Also note that the aileron and rudder channels will need to be reversed.
In OpenTX, 100% travel is equivalent to 125% in a Spektrum transmitter. Not only will the servos overtravel if the Taranis is set to 100% limits, but in some cases the SAFE system reacts badly to the increased pulse width. Also, the ESC is expecting to see Spektrum limits.
Also note that the aileron and rudder channels will need to be reversed.
-
- Posts: 121
- Joined: Wed Dec 02, 2015 9:25 pm
- Country: United Kingdom
Re: how may I change the default switch position to be -100 low on a taranis x7 to emulate a DX5e SAFE BNF RX
Cheers Jimjtaylor wrote: ↑Sat Jun 10, 2017 10:31 am The documentation that thebrairs0 did is the best I have seen. It is for openTX 2.1 but most applies to 2.2 viewtopic.php?f=45&t=8724
Jim
Intend to start on the 2.2 version once it has been updated a bit more to include all the Horus features.