New version of eePskye for erSky9x r219?

eepSKYe is the desktop too for flashing and managing your sky9x firmware.
Post Reply
benzo99
Posts: 12
Joined: Sat Nov 05, 2016 10:39 am
Country: -

New version of eePskye for erSky9x r219?

Post by benzo99 »

Is there a version of eePskye which supports the updates in the latest ersky9xr builds, specifically the new protocol options for the multi-protocol module? I'm trying to set my models up in eePskye but every time I write the memory back to the Tx I have to modify the protocol settings on the Tx because the FRSKYX protocol isn't available in eePskye. Not a big deal, just wondering if I've missed a test version somewhere.

Second question - could the eePskye simulator show the flight mode? I'm trying to set my switches to show the right flight mode correctly and it would be much easier of I could do it in the simulator.

That said, the software is awesome :-)

User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

I'll post an update on the ersky9x test versions thread later today.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

Posted!

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
benzo99
Posts: 12
Joined: Sat Nov 05, 2016 10:39 am
Country: -

Re: New version of eePskye for erSky9x r219?

Post by benzo99 »

MikeB wrote:Posted!

Mike.
Thanks for the quick response! The flight mode shows up perfectly, but there's something weird happening with the multi-protocol protocol settings...

I have two models, one configured for FrSkyX CH_16, the other configured for Bayang. Both are fully configured in the Tx menu. If I read the memory from the TX, then look at the Bayang model all the sub-protocol options are blank. If I look at the FrSkyX model everything looks right the first time I open it, but if I close the editor and go back the sub-protocol options are all blank.
User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

I've replaced the test version with an updated one, see if that is any better.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

benzo99
Posts: 12
Joined: Sat Nov 05, 2016 10:39 am
Country: -

Re: New version of eePskye for erSky9x r219?

Post by benzo99 »

It is better, but still not quite right. The model configured for FrSkyX works as expected, but the Bayang model is still blank when read from the Tx. If I set it to Bayang and write the EEPROM everything is fine when checked on the Tx.

Ben
User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

It's working OK for me. I configured a model to Multi/Bayang, then read it into eepskye and Bayang was displayed correctly. I've checked this on a SKY board, an AR9X board and a 9XR-PRO.
If you set Bayang on eepskye, write it to the radio then read it back, does it work OK then?

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
benzo99
Posts: 12
Joined: Sat Nov 05, 2016 10:39 am
Country: -

Re: New version of eePskye for erSky9x r219?

Post by benzo99 »

OK, I did a bit more testing - the problem only occurs when setting Autobind to Yes.

If I read a model with Bayang protocol and autobind enabled the subprotocol is blank. Likewise, if I create a model and choose Bayang and autobind, close the model and go back in the subprotocol is blank.

This seems to happen for all subprotocols when enabling autobind.

Ben
User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

I should have fixed this "autobind" problem in the version I've just posted.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
benzo99
Posts: 12
Joined: Sat Nov 05, 2016 10:39 am
Country: -

Re: New version of eePskye for erSky9x r219?

Post by benzo99 »

Looks good to me. Thanks so much - I'm blown away by the speed you turned that around. My day job is in IT, and we have paid-for software that doesn't get support this good. How does one send you beer money?

Ben
User avatar
MikeB
9x Developer
Posts: 17979
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: New version of eePskye for erSky9x r219?

Post by MikeB »

In eepskye, call up Help|About and there is a "donating" link there!
Or, find one of "JHSA"s posts and there is a link at the bottom.

Thanks.

Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: New version of eePskye for erSky9x r219?

Post by jhsa »

There's a link under my posts for donating to Mike.

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

Post Reply

Return to “eepSKYe”