FS-TH9X 9xtreme ersky9x dht RSSI
FS-TH9X 9xtreme ersky9x dht RSSI
Hi. radio FS-TH9X board 9xtreme dht module.
settings: TELEMETRY FrSky com pot 1 - invert COM1
radio show rx tx value
how to set alarm rssi?
I experiment: set RSSI Warn 65 - RSSI Critical 60
moving away from the receiver -----Show tx=62
alarm voice "no telemetry" simultaneously rx=0 tx=0
something is wrong?
thanks
settings: TELEMETRY FrSky com pot 1 - invert COM1
radio show rx tx value
how to set alarm rssi?
I experiment: set RSSI Warn 65 - RSSI Critical 60
moving away from the receiver -----Show tx=62
alarm voice "no telemetry" simultaneously rx=0 tx=0
something is wrong?
thanks
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: FS-TH9X 9xtreme ersky9x dht RSSI
The standard settings are 45 and 42 and the 'D' link usually works fine down to these values.
When close to the receiver, you should see RSSI and TSSI showing 90 to 100.
As you move away, do both RSSI and TSSI (Rx= and Tx=) values both drop at about the same rate?
Mike.
When close to the receiver, you should see RSSI and TSSI showing 90 to 100.
As you move away, do both RSSI and TSSI (Rx= and Tx=) values both drop at about the same rate?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: FS-TH9X 9xtreme ersky9x dht RSSI
Put the DHT in range test mode and do a proper range test.
You should get more than 50 meters without losing signal and the servos stopping..
João
You should get more than 50 meters without losing signal and the servos stopping..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FS-TH9X 9xtreme ersky9x dht RSSI
ok thanks! I try tomorrow.
65 and 60 was only a test, more easy to get , into the house.
I'm curious to know ,,Question: I do not see values A1 and A2, why?
I hope it is understandable sorry my bad english
65 and 60 was only a test, more easy to get , into the house.
I'm curious to know ,,Question: I do not see values A1 and A2, why?
I hope it is understandable sorry my bad english
Re: FS-TH9X 9xtreme ersky9x dht RSSI
Do you have any sensors connected to A1 or A2 on the receiver? For example a voltage sensor?
By the way, what receiver do you have?
João
By the way, what receiver do you have?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FS-TH9X 9xtreme ersky9x dht RSSI
aahm ...ok no sensor !! now I understand!!
FrSky D4R-II and rx f802 fw midelic
I'd like to get tx rx alarm function thanks
FrSky D4R-II and rx f802 fw midelic
I'd like to get tx rx alarm function thanks
Re: FS-TH9X 9xtreme ersky9x dht RSSI
The radio already alarms those by default. Check the telemetry menu.. and you can change the alarm values there as well..
João
EDIT: and it is quite easy to make your own voltage sensors..
I think the D4R-II only has the A2 available for an external sensor, and A1 is connected to it's own supply.
Go to the telemetry menu and set A1 range to 13.2. Then you should see the receiver voltage on A1.
Attention, i said receiver voltage, not battery voltage unless you are powering the receiver directly from the battery without a BEC.
Try that
João
João
EDIT: and it is quite easy to make your own voltage sensors..
I think the D4R-II only has the A2 available for an external sensor, and A1 is connected to it's own supply.
Go to the telemetry menu and set A1 range to 13.2. Then you should see the receiver voltage on A1.
Attention, i said receiver voltage, not battery voltage unless you are powering the receiver directly from the battery without a BEC.
Try that
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FS-TH9X 9xtreme ersky9x dht RSSI
Bingo! rx 802 sends wrong signal (rx steady 97-95 even if I move away)
Bingo! D4R-II set A1= 13.2v Display A1=5.0
and voice alarm it work "receiver signal low" "receiver signal critical"
I'm sorry guys I am a great great beginner
very kind thanks!!
Re: FS-TH9X 9xtreme ersky9x dht RSSI
we are always learning
By the way, I have built some 802, a bit better than the ones banggood sell as mine have antenna diversity, and the RSSI and TSSI behave normally.. these are full range receivers..
They also have protection against swamping. I can touch the TX antenna on the RX antenna and there are no swamping problems, thanks to the great work Midelic did on the code..
João
By the way, I have built some 802, a bit better than the ones banggood sell as mine have antenna diversity, and the RSSI and TSSI behave normally.. these are full range receivers..
They also have protection against swamping. I can touch the TX antenna on the RX antenna and there are no swamping problems, thanks to the great work Midelic did on the code..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: FS-TH9X 9xtreme ersky9x dht RSSI
really good diy job! I already have seen on rc group. How did you engrave small pcb !?
Re: FS-TH9X 9xtreme ersky9x dht RSSI
Small PCB?
The blue one belongs to the RF module we buy from Banggood.
I made the other 2. The main board and the switch board where the blue module is soldered.
I will make a build thread soon..
João
The blue one belongs to the RF module we buy from Banggood.
I made the other 2. The main board and the switch board where the blue module is soldered.
I will make a build thread soon..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW