Hi All
I have a APM 2.6 to control a quad wooden house made and Turnigy er9x for which I have configured
the 6 flightmodes on Channel 5. It flies correctly. After some testing, I interested on move an simple
gimbal with an 9g servo.
I use mission planner Version 1.3.37 and arducopter 3.2.1 release
On my Turnigy ER9x I want to use Pot2 to move them.
In mixer I write CH6 100 SwitchGEAR but it does not work.
I have also set CH7 100 sGear and CH8 100 sEle
I also checked in radio calibration of Mission Planner that all the meters move from mini to maxi,
including radio5, which takes 6 positions depending on the flight mode, but no move on CH 6-7-8
What is wrong or what I forgot?
Thanks for your help.
How setup AUX channels (6-7_8)
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: How setup AUX channels (6-7_8)
Try setting the source of CH6 to P2, and nothing in the switch setting.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: How setup AUX channels (6-7_8)
Mike thank you to take care of my problem.
I tested your suggestion but no change
I tested your suggestion but no change
Re: How setup AUX channels (6-7_8)
Can't see the pictures.. Can you post them directly here??
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: How setup AUX channels (6-7_8)
I have not found on Turnigy er9X how to enable or disable chanels other than giving values to the mix.
Re: How setup AUX channels (6-7_8)
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: How setup AUX channels (6-7_8)
One of the main screens shows horizontal bars for the positions of the channels. Do the bars for channels 6, 7 and 8 move when you operate the controls?
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: How setup AUX channels (6-7_8)
If there is no mix on a channel, the value will be 1500. In other words, it is disabled.
To enable a channel, create a mix.
For example 100% P2 will cause the output to vary from 988 to 2012 with a turn of the knob.
Or 100% FULL AIL will produce -988 and 2012 depending on the position of the AIL switch.
It's all explained in the 2015 ER9X manual, which can be found at www.er9x.com
To enable a channel, create a mix.
For example 100% P2 will cause the output to vary from 988 to 2012 with a turn of the knob.
Or 100% FULL AIL will produce -988 and 2012 depending on the position of the AIL switch.
It's all explained in the 2015 ER9X manual, which can be found at www.er9x.com
Re: How setup AUX channels (6-7_8)
Oops! my post has gone by the wayside!
I connected an oscilloscope to the input of RF module and found that there
were 9 crenel and a sync top.
All switches or pots that are assigned to a channel, are shaking the respective crenel.
So the problem is not the tgy 9X but the Mission Planner.
Thank you again for your help.
Bernard
I connected an oscilloscope to the input of RF module and found that there
were 9 crenel and a sync top.
All switches or pots that are assigned to a channel, are shaking the respective crenel.
So the problem is not the tgy 9X but the Mission Planner.
Thank you again for your help.
Bernard