Turnigy 9X backlight timeout not working
Turnigy 9X backlight timeout not working
Hi Guys,
I recently bought Turnigy 9x V2 and backlight kit from hobbyking, and also purchased a smartieparts programmer board(v2.4).
I flashed er9x, after i set the backlight timeout to 10sec and ER9X managed to switch off the backlight after 10sec.
But today, it is not working.
i tired to re-flash ER9x, but no luck
Any advice?
I recently bought Turnigy 9x V2 and backlight kit from hobbyking, and also purchased a smartieparts programmer board(v2.4).
I flashed er9x, after i set the backlight timeout to 10sec and ER9X managed to switch off the backlight after 10sec.
But today, it is not working.
i tired to re-flash ER9x, but no luck
Any advice?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9X backlight timeout not working
Try setting the timeout to 0 and assigning a switch. Then test to see if the backlight will turn on and off.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9X backlight timeout not working
Hi Mike,
set to 0. but still the same. the backlight is still always on.
Last night when i toggle the "Backlight Invert", i am able to see the backlight switch off and on.
but now no matter what i do the backlight never goes off.
set to 0. but still the same. the backlight is still always on.
Last night when i toggle the "Backlight Invert", i am able to see the backlight switch off and on.
but now no matter what i do the backlight never goes off.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9X backlight timeout not working
What have you got the "sound mode" set to on the RADIO SETUP menu?
If you fit a MegaSound board to get voice, it uses the backlight control pin for voice control. You then set the "sound mode" to either beeperVoice or pispkrVoice. The backlight is then controlled from the MegaSound board.
So if you have accidently set the "sound mode" to include voice, the backlight stops working.
Mike.
If you fit a MegaSound board to get voice, it uses the backlight control pin for voice control. You then set the "sound mode" to either beeperVoice or pispkrVoice. The backlight is then controlled from the MegaSound board.
So if you have accidently set the "sound mode" to include voice, the backlight stops working.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9X backlight timeout not working
Hi Mike,
Amazing!!!!! it works.
You are great!!!! thanks Bro!!!!
Amazing!!!!! it works.
You are great!!!! thanks Bro!!!!
Re: Turnigy 9X backlight timeout not working
Hi Mike,
Amazing!!!!! it works.
You are great!!!! thanks Bro!!!!
Amazing!!!!! it works.
You are great!!!! thanks Bro!!!!
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Turnigy 9X backlight timeout not working
Mike makes us all seem smarter then we are.
Re: Turnigy 9X backlight timeout not working
Hello,
May be I reanimate this thread, please could you help me with the same problem.
I have tanker9x installed and timeout not working on my lcd. It is set to beeper. No matter what I do, lcd does not go off. I did set it to 5 sec.
Please advice.
Andrey
May be I reanimate this thread, please could you help me with the same problem.
I have tanker9x installed and timeout not working on my lcd. It is set to beeper. No matter what I do, lcd does not go off. I did set it to 5 sec.
Please advice.
Andrey
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Turnigy 9X backlight timeout not working
Please give more info.
To have BL led control you must do the control mod.
Did you do the FET or transistor control mod? Is it connected to pin 17 of the CPU? Does it go out if pin 17 is disconnected?
SM
Sent from my iPod touch using Tapatalk, small keys and a big finger.
To have BL led control you must do the control mod.
Did you do the FET or transistor control mod? Is it connected to pin 17 of the CPU? Does it go out if pin 17 is disconnected?
SM
Sent from my iPod touch using Tapatalk, small keys and a big finger.
Re: Turnigy 9X backlight timeout not working
Thanks that has helped.
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Turnigy 9X backlight timeout not working
Helped in what way please?
Re: Turnigy 9X backlight timeout not working
I had the same problem with the 9X, SmartieParts Board and the Hobby King backlight.
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Turnigy 9X backlight timeout not working
Did you fix it? What SP board model? Newer led version or older EL version that you would use the VDD connection to drive the added DIY FET switch?lostcity wrote:I had the same problem with the 9X, SmartieParts Board and the Hobby King backlight.
I'm just trying to sort out the short answers to see what's been done. I've done BL sw conversions, some with SP boards of different models that all worked.
Re: Turnigy 9X backlight timeout not working
Newer version rev 2.4 and. 9x v2. Installed per the Smartieparts website.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- ShowMaster
- Posts: 4327
- Joined: Thu Dec 29, 2011 3:44 am
- Country: -
- Location: Los Angeles, CA USA
Re: Turnigy 9X backlight timeout not working
The VDD pin on the sp board or pin 17 on the CPU should toggle from 0 to 3.3v when the BL function is working. I don't have the newer so board to test with but that's how simple it it is. 3.3v on CPU pin 17(VDD SP board) BL is on. 0 volts BL
Is off. Of you have 3.3v full time on pin 17 or VDD then it's a setting in the FW menu most likely.
The first page of the radio setup menu has those settings and switch options for the BL.
Not much more I can offer as this has solved all if any BL issues I've had.
SM
Is off. Of you have 3.3v full time on pin 17 or VDD then it's a setting in the FW menu most likely.
The first page of the radio setup menu has those settings and switch options for the BL.
Not much more I can offer as this has solved all if any BL issues I've had.
SM