er9x wiper mixer

er9x is the best known firmware. It has a superb range of features and is well supported by the community. Well worth trying out.
Post Reply
Tester
Posts: 9
Joined: Mon Aug 04, 2014 12:40 pm
Country: -

er9x wiper mixer

Post by Tester »

Hello,

I try with the servo test function, over a servo a wiper to imitate.
Unfortunately, I do not get it to turn off the function, the servo to the right (or to the left) runs to the stop and stops.
Does anyone have a tip for me? So my mixer looks like: (at CH06 sits the servo)
CH06 R +100%CH15
*
*
*
CH15 +100%CH16Schalter(THR)Langsam/u5:d)
CH16 +110%FullSchalter(L1)
R -110%HalfSchalter(L2)
R+110%HalfSchalter(L3)

Thanks Dirk

Hallo,

ich versuche mit der Servo Test Funktion, über ein Servo einen Scheibenwischer zu imitieren.
Leider Bekomme ich es nicht hin das beim Ausschalten der Funktion das Servo nach rechts ( oder nach links) bis zum Anschlag läuft und stehen bleibt.
Hat jemand einen Tipp für mich? So sieht mein Mischer aus: (an CH06 sitzt das Servo)
CH06 R +100%CH15
*
*
*
CH15 +100%CH16Schalter(THR)Langsam/u5:d)
CH16 +110%FullSchalter(L1)
R -110%HalfSchalter(L2)
R+110%HalfSchalter(L3)

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: er9x wiper mixer

Post by jhsa »

If I understand what you're trying to do, it is very easy.

Logical switches:

Use the Timer function.

L1 Timer Off 2 ON 2 AND RUD (Switch to trigger the timer)

Then Mixer:

CH6 100% FULL Switch (L1) Slow (u2 : d2)

That's it. Ahhh, setting the weight at more than 100% in this case is useless as you might have the limits set to 100% anyway. If you need more servo movement, enable "E.Limits" (extended limits) in the model settings, and set the limits to more than 100%. But leave the mixer at 100%..

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
ReSt
Posts: 1581
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: er9x wiper mixer

Post by ReSt »

Or to always get a full sweep cycle

Switch on AIL and the wiper starts. Switch off AIL and the wiper completes its cycle and then stops (always on the same side)

CH6 FULL 100% SW(L1) SLOW(up 3, down 3)
L1 TIMEOFF 3 ON 3 L3
L2 v<val CH6 -97 L4
L3 XOR L2 ON
L4 XOR AIL ON

L3 and L4 are only required to invert L2 and AIL as the switches are not available as inverted switches.
L3 = !L2 and L4 = !AIL

Reinhard
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: er9x wiper mixer

Post by jhsa »

Nice way to emulate the "inverted switch" using the XOR function :)
I never thought about that :)

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
ReSt
Posts: 1581
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: er9x wiper mixer

Post by ReSt »

Another possibility, without Inverters

CH6 FULL 100% Sw(L1) Slow(up:3, down:3)

L1 TimeOff 3 On 3 L2
L2 Latch AIL L3
L3 v<val CH6 -97

The "Latch" is activated with AIL switch. And with AIL switch activ it stays active even when the Reset L3 is active.
It is reset when the AIL switch is no longer active AND CH6 < -97

So you need a 2 position switch to switch your wiper ON or OFF

Reinhard

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: er9x wiper mixer

Post by jhsa »

And uses one less logical switch :)
Also if you want to use a momentary switch (like the TRN switch) instead of a two position switch to turn this ON and OFF, just use a flip-flop function.

L4 F-Flop TRN !L4

Replace AIL switch in L2 with L4..
Hit the TRN switch once to turn it ON, and hit it again to stop. :)
This is fun ;) :mrgreen:
João

Sent from my thor using Tapatalk




My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Tester
Posts: 9
Joined: Mon Aug 04, 2014 12:40 pm
Country: -

Re: er9x wiper mixer

Post by Tester »

Hello and thanks,
I actually thought, as I have read from Reinhard I do not get that. But it's running. Although I did not understand everything I was doing. I have taken the first version of Reihnert. The speed I get changed also.
What do I have to do when I want to turn the servo's end stop, is now left when switching off?
Dirk

HALLO Und Danke,
Ich hab eigentlich gedacht , wie ich das von Reinhard gelesen habe ich bekomme das nicht hin. Aber es läuft. Obwohl ich nicht alles verstanden habe, was ich da mache. Ich habe die erste Version von Reinhard genommen. Die Geschwindigkeit bekomme ich auch geändert.
Was muß ich machen wenn ich den End Anschlag des Servos drehen will, jetzt ist beim Ausschalten jetzt links?
Dirk
ReSt
Posts: 1581
Joined: Tue Dec 27, 2011 11:34 pm
Country: -

Re: er9x wiper mixer

Post by ReSt »

To stop the servo on the other side do the following
in the channel mix change the amout from +100% to -100%

and change the logic switch that compares the channel value
from v<val CH6 -97 to v>val CH6 +97

That should do it.

Reinhard

Post Reply

Return to “er9x”