Will OpenTx display sbus telemetry with 9x radio LCD?
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Will OpenTx display sbus telemetry with 9x radio LCD?
I've looked and keep finding only older posts. I'm hoping someone here will brighten my day with an unexpected "yes, it will work"
Very simple question: I keep seeing that a 9x radio+OpenTx+XJT module will not properly display telemetry data on the 9x lcd.
Is this the case?
I know a co pilot display will do it, but I want it on my 9x display.
Thanks!
Very simple question: I keep seeing that a 9x radio+OpenTx+XJT module will not properly display telemetry data on the 9x lcd.
Is this the case?
I know a co pilot display will do it, but I want it on my 9x display.
Thanks!
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Smart port telemetry support (I imagine SBUS is a mixup) has unfortunately never been added for the 9x in OpenTX. All OpenTX developers having moved away from the 9x before that appeared nobody got interested in doing the work. Still possible of course, but would likely take someone with interest to join the project and add support.
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
The 9X does need a hadware mod (inverter and two signals moved to other pins) to receive telemetry from either a DJT or a XJT.
Er9x firmware does support handling and displaying SPort telemetry data.
Mike.
Er9x firmware does support handling and displaying SPort telemetry data.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Dernit. I had delusions of using of using XJT in a DIY Mega2560 radio...
Que sera
Que sera
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
WAIT!!!!!!!!!!!
I see there is a mega2561 build for ER9X. I assume this can be flashed to a diy 2560? same schematics as the OpenTx DIY 2560?
Am I right?
I see there is a mega2561 build for ER9X. I assume this can be flashed to a diy 2560? same schematics as the OpenTx DIY 2560?
Am I right?
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
The 2 chips are significantly different even if their names aren't... don't think it will port straight.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
I don't know specifically. The build of er9x works on a 9X with the '64 replaced by a '2561, so is only using the 64 pins of the '2561 and these are connected to the same functions therefore.
I think the openTx build matches the "Gruvin" board and uses a different connection layout.
If you use the same connections as used on the 9X, then the er9x-2561 build should work.
Mike.
I think the openTx build matches the "Gruvin" board and uses a different connection layout.
If you use the same connections as used on the 9X, then the er9x-2561 build should work.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Bear with me, please:
The 2560 and 2561 are not "compatible" for this application? What is the important difference?
****EDIT* The pinouts are different and obviously programming would not interact as programmed for the other chip.***
I have since started found the 9x clone thread
and will do lots of reading before I build my own TX, I'm sure.
Thanks VERY MUCH for the info, ya'll!
****EDUT2** I'm going to start a new thread elsewhere to pursue my own 9x clone with a 2561 (or other compatible chip) so I can use XJT telemetry, but only after a lot more reading.****
The 2560 and 2561 are not "compatible" for this application? What is the important difference?
****EDIT* The pinouts are different and obviously programming would not interact as programmed for the other chip.***
I have since started found the 9x clone thread
and will do lots of reading before I build my own TX, I'm sure.
Thanks VERY MUCH for the info, ya'll!
****EDUT2** I'm going to start a new thread elsewhere to pursue my own 9x clone with a 2561 (or other compatible chip) so I can use XJT telemetry, but only after a lot more reading.****
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Look at the AR9X and ARUni boards, you've got all the goodies of ARM radios completely integrated and with full support for jsut $30. No point bothering with anything else nowadays unless you actually want to figure out everything for the fun of it.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Thank you, but this is more of a pet project/desire/learning experience. I already have a 9x capable of running ER9x and supporting the XJT telemetry.
I just wanna build a badass radio to show off, I guess..... posterity, that sort of thing.
I do appreciate all the info, comments, and advice!
I just wanna build a badass radio to show off, I guess..... posterity, that sort of thing.
I do appreciate all the info, comments, and advice!
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Let's pretend I'm going to build a radio based on a 9x processor.
Which ER9X image will support XJT telemetry and voice?
Thanks, again!
Which ER9X image will support XJT telemetry and voice?
Thanks, again!
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
I would say all of them.
But if you really want a badass radio to show off it's features, then you need one like mine with Ersky9x of course
Get an Ar9x board and start loading hardware on it
https://www.youtube.com/watch?v=2-kZZPydQdw
https://www.youtube.com/watch?v=VlmBIASrMwM
João
But if you really want a badass radio to show off it's features, then you need one like mine with Ersky9x of course
Get an Ar9x board and start loading hardware on it
https://www.youtube.com/watch?v=2-kZZPydQdw
https://www.youtube.com/watch?v=VlmBIASrMwM
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Dude, that is sick! I have a few questions, though:
what is the real time clock for?
er9x for the ar9x has programming for extra buttons built in? is it setup/selected in the 9x, or in the firmware before you flash?
what are the 4 buttons on the back for (what do *you use them for)?
Does internal module transmit when you have external module installed?
I wanted to build my own radio for 2 reasons; to learn about the guts of a radio and everything that goes into it, and also to make a case that was the size I wanted and laid out how I wanted. I love opentx, but I think my needs/desires have changed...I might trick out my 9x as my main radio and still build extra(s) transmitters!
Damnit. this Rc hobby thing is an endless rabbit hole of new toys! ;D
what is the real time clock for?
er9x for the ar9x has programming for extra buttons built in? is it setup/selected in the 9x, or in the firmware before you flash?
what are the 4 buttons on the back for (what do *you use them for)?
Does internal module transmit when you have external module installed?
I wanted to build my own radio for 2 reasons; to learn about the guts of a radio and everything that goes into it, and also to make a case that was the size I wanted and laid out how I wanted. I love opentx, but I think my needs/desires have changed...I might trick out my 9x as my main radio and still build extra(s) transmitters!
Damnit. this Rc hobby thing is an endless rabbit hole of new toys! ;D
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
You can log several parameters from your flights on the SD Card. Stuff like telemetry values, etc. For that you need an RTC that provides time and date.
I also use it as an A.D.T. (Anti Divorce Tool) I Just set an alarm telling me that is time to pack my stuff and go home
It is all configured in the Ersky9x "Radio Setup / Hardware" menu. This menu is protected so stuff doesn't get changed by accident.er9x for the ar9x has programming for extra buttons built in? is it setup/selected in the 9x, or in the firmware before you flash?
You can use them for may things, just like a normal switch for example. Just configure a Logical switch as a Flip-Flop, and when you press them once, the Logical switch turns ON, press it again, and the logical switch turns OFF. Use the logical switch to control a mix. You can control stuff like lights, etc...what are the 4 buttons on the back for (what do *you use them for)?
I use them mostly to play voice messages, when I want to know the plane's battery voltage for example, or want to reset the timer, stuff like that.
Well, this depends on whether you built the circuit to control the power to both modules, please see here:Does internal module transmit when you have external module installed?
http://openrcforums.com/forum/viewtopic.php?f=85&t=8471
Ersky9x can turn the pulses to both internal and external modules OFF. The circuit linked above detects this and turns the power to the respective module OFF. As soon as you select a protocol, Ersky9x starts sending a signal to the module, the circuit detects the signal and turns the Power ON.
If you don't have this circuit, both modules will be powered when the radio is turned ON, and therefore transmitting..
If you want to build your own case/radio, you might like to have a look at this board then. It is basically the same as the Ar9x but designed to revive old radios and also for projects like the one you've just described.I wanted to build my own radio for 2 reasons; to learn about the guts of a radio and everything that goes into it, and also to make a case that was the size I wanted and laid out how I wanted. I love opentx, but I think my needs/desires have changed...I might trick out my 9x as my main radio and still build extra(s) transmitters!
https://www.rcgroups.com/forums/showthr ... rsal-board
All the above applies to this board as well..
You tell meDamnit. this Rc hobby thing is an endless rabbit hole of new toys! ;D
João
EDIT: Both boards run OpenTX as well. But I think it doesn't allow for any extra hardware apart from what a 9x radio has.
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Jsha, can I add bluetooth to atmega64 for er9x? I found a couple threads where it was discussed (including you), but never saw where a how to.
I know AR9x will do it.
I know AR9x will do it.
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
I don't think it supported on boards with Atmega processors. At least not the way we use it. Trainer, etc..
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
That's what I thought. I was hoping I was wrong. Lol
Thx!
Thx!
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
People have been putting BT modules in them back then but it was for example connected straight to the RF module to relay the telemetry, i.e. not actually involving the radio at all.
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Or you could upgrade your radio with an Ar9x board. They are cheap and good..interestingfellow wrote: ↑Tue Mar 28, 2017 5:41 pm That's what I thought. I was hoping I was wrong. Lol
Thx!
I have a couple.
Check ar9x.net if you want to have a look.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
I'm sold on the idea of the AR9x, at this point it's a matter of budget and time. Soon...
I keep asking about m64/m128 chips because I have a walkera donor tx that I'm going to convert with an m64, and then maybe build a teeny tiny one for fun, just because I have the parts. I really want to learn programming and hardware, hence all the screwing around.
I was hoping the m64 could bluetooth trainer to the converted Walkera with m64, but whatever. A cable isn't going to kill me.
Thanks, again!
I keep asking about m64/m128 chips because I have a walkera donor tx that I'm going to convert with an m64, and then maybe build a teeny tiny one for fun, just because I have the parts. I really want to learn programming and hardware, hence all the screwing around.
I was hoping the m64 could bluetooth trainer to the converted Walkera with m64, but whatever. A cable isn't going to kill me.
Thanks, again!
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
OK!
Jhsa:
why would I want LCD extension with AR9x?
Original 9x LCD/backlight works with new board?
What is "programing S-port device from transmitter"? Where is the S-port device located (Tx module? rx?)?
Thx! TTYS!
Jhsa:
why would I want LCD extension with AR9x?
Original 9x LCD/backlight works with new board?
What is "programing S-port device from transmitter"? Where is the S-port device located (Tx module? rx?)?
Thx! TTYS!
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
The Ar9x board (Not the ArUni) is a direct replacement of the 9x board. That means it will work with the 9x LCD without any extension.
The extension is used if mounting the board in another different cases.
The update S.Port function in Ersky9x allows you to program the Frsky XJT module and X series receivers with new firmware.
There are other hardware updates you can do with Ersky9x using the radio..
João
Sent from my thor using Tapatalk
The extension is used if mounting the board in another different cases.
The update S.Port function in Ersky9x allows you to program the Frsky XJT module and X series receivers with new firmware.
There are other hardware updates you can do with Ersky9x using the radio..
João
Sent from my thor using Tapatalk
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
perfect answers.
Thanks!!!
Thanks!!!
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Debating on upgrading my 9x with AR9x and M9's OR scratch building a radio case like this one with an UNI and M9's https://www.rcgroups.com/forums/showpos ... stcount=15
that way, I would have the 9x with dsm and also custom with xjt...
that way, I would have the 9x with dsm and also custom with xjt...
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Also, xjt and 9x *is possible.. i thinkhttp://jb0.de/?p=298
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
I ordered the AR9x and a couple M9's for my 9x.
Adding rtc, encoder nav pad, a couple extra buttons, another 3 way switch, and want to do custom paint and grips.
We'll see how far I get...
Adding rtc, encoder nav pad, a couple extra buttons, another 3 way switch, and want to do custom paint and grips.
We'll see how far I get...
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
What firmware are you using?
This is an openTX thread, but as far as I know openTX at this moment does not support any extra switches and buttons on the Ar9x board. And I don't know if it ever will, as it looks lime there is not much interest from the developers on this board.
João
Sent from my thor using Tapatalk
This is an openTX thread, but as far as I know openTX at this moment does not support any extra switches and buttons on the Ar9x board. And I don't know if it ever will, as it looks lime there is not much interest from the developers on this board.
João
Sent from my thor using Tapatalk
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 213
- Joined: Tue Jun 16, 2015 2:05 am
- Country: United States
- Location: durham, nc
Re: Will OpenTx display sbus telemetry with 9x radio LCD?
Right nowOpenTX.
But after, I will be using Ersky9x.
But after, I will be using Ersky9x.