Setting up Serial Communications with Tx Module
Setting up Serial Communications with Tx Module
I recently ordered a multiprotocol Tx and am trying to set my controller up for when it arrives. I have loaded version 2.2.1 on my Turnigy 9x with m128 board but I cannot find where to switch between PPM and serial communication with the Tx module. The multimodule website (https://github.com/pascallanger/DIY-Mul ... mitters.md) states that this should work with a 9x and openTx but I cannot find the setting anywhere. Any help? Thanks!
Re: Setting up Serial Communications with Tx Module
RCdiy.ca
Stay Safe & Have Fun
OpenTX Manual http://rcdiy.ca
Paying it forward by sharing my Lua scripts, documentation and videos.
Stay Safe & Have Fun
OpenTX Manual http://rcdiy.ca
Paying it forward by sharing my Lua scripts, documentation and videos.
Re: Setting up Serial Communications with Tx Module
As the table on that link shows with a 9x your only option is er9x.
Re: Setting up Serial Communications with Tx Module
I do not have that option. I was digging deeper into the multiprotocol page and it states that serial communication is only supported by er9x firmware for the Turnigy 9x (https://github.com/pascallanger/DIY-Mul ... skyTH9X.md). I thought I had read that it was available through openTx too but I guess I was mistaken.rcdiy wrote: ↑Fri Jan 19, 2018 5:03 pm Model setup screen
At the bottom
External RF
http://rcdiy.ca/opentx-guide/opentx-tra ... del-setup/
See above. I guess that I will have to switch firmware. Thanks for the help!
Re: Setting up Serial Communications with Tx Module
That page was last updated
Apr 19, 2017
@LapinFou LapinFou Update Tx-FlyskyTH9X.md
Since then OpenTX has added support...
BUT.... you are off-course 100% correct m128 does not have the build option in companion....
Apologies:)
Apr 19, 2017
@LapinFou LapinFou Update Tx-FlyskyTH9X.md
Since then OpenTX has added support...
BUT.... you are off-course 100% correct m128 does not have the build option in companion....
Apologies:)
RCdiy.ca
Stay Safe & Have Fun
OpenTX Manual http://rcdiy.ca
Paying it forward by sharing my Lua scripts, documentation and videos.
Stay Safe & Have Fun
OpenTX Manual http://rcdiy.ca
Paying it forward by sharing my Lua scripts, documentation and videos.
Re: Setting up Serial Communications with Tx Module
OpenTX as far as I know, doesn't have multiprotocol serial support on the stock 9x mainboard, and that is what the multiprotocol site states.
If you want to use it with openTX on a stock 9x radio, you will have to use PPM, and configure it with the module's multi position switch..
João
If you want to use it with openTX on a stock 9x radio, you will have to use PPM, and configure it with the module's multi position switch..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW