Page 1 of 1
9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Thu Jan 19, 2017 2:17 pm
by airwolfe
Hello, need some help, I have a bnf fpv inductrix and I just got the 4n1 module and I get it to bind finally. However, it will not move. Nothing I do to the control results in any action from the drone. I have my settings for the mutli protocol dsm(DSMX-22, autobind =y, 8ch, rxnum8, trainer polarity pos, power=high, rate 7ms, 1st chan=6, module tx and rx nodes on the board are bridged.
Please help...
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Thu Jan 19, 2017 2:23 pm
by MikeB
Why first chan = 6? Try setting this back to 1.
If first chan is set to 6, then the mixer channels 1 to 5 are not being used, channel 6 is sent as channel 1 to the module.
Mike.
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Thu Jan 19, 2017 7:55 pm
by airwolfe
MikeB wrote:Why first chan = 6? Try setting this back to 1.
If first chan is set to 6, then the mixer channels 1 to 5 are not being used, channel 6 is sent as channel 1 to the module.
Mike.
Thx, I will check that when I get home. And again for being patient I'm new to all this..
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Thu Jan 19, 2017 10:39 pm
by airwolfe
Mike, I changed it to ch1 and it seems to bind but the controls are wonkie.
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 12:01 am
by airwolfe
airwolfe wrote:Mike, I changed it to ch1 and it seems to bind but the controls are wonkie.
it does seem to turn on the motors atleast
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 4:05 am
by airwolfe
Everything is in reverse. my right sticket controls the throttle to some degree but only at a angle.(bottom left) which also activates the drone.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 6:28 am
by LutzB
Please check your channel order: 1=T, 2=A, 3=E, 4=R, 6=Mode
I am using a taranis with a old DX4 module, so it might be different to your setup. But this is the way it works for me. You can also search for a NanoQX setup, as it is the same configuration.
Lutz
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 6:48 am
by jhsa
If he is using the 4 in 1 multi module, I believe the channel order should be AETR?
Also what stick mode do you fly? Is your throttle on the left, or on the right?
João
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 8:35 am
by Kilrah
Yes, multimodule needs AETR.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 1:34 pm
by airwolfe
my throttle is on the left. mode2 however I had to change it to mode 1 to make the drone work correctly some what.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 1:51 pm
by Kilrah
That will work but is not correct, you should leave it in mode 2 and change ordering in the mixer.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 4:16 pm
by airwolfe
ooh ok, I will do that. I got it to fly but its like on the throttle there is a dead spot and its not all the way down. All the way down goes in reverse... when I get home I will work on it some more.
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 4:22 pm
by jhsa
Did you calibrate your radio's sticks?
João
Re: RE: Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 4:26 pm
by airwolfe
jhsa wrote:Did you calibrate your radio's sticks?
João
I believe so but I will do that again when I get home. Thx for the help.
Sent from my SM-G920V using Tapatalk
Re: 9XR Pro + Multiiprotocol + Inductrix FPV
Posted: Fri Jan 20, 2017 4:49 pm
by LutzB
airwolfe wrote:ooh ok, I will do that. I got it to fly but its like on the throttle there is a dead spot and its not all the way down. All the way down goes in reverse... when I get home I will work on it some more.
I also noticed this behavior on the throttle channel. I had to raise the min value quite a lot.