openrcforums

my er9x firmware is not showing the whole or all the choices in the control section I'm missing the ppm option how or what did I do wrong what do I need to do re flashed twice AND STILL SAME ISSUE does anyone no why please help need to get back up in the air

Sounds unusual! The PPM settings are in the model setup, under "protocol". Is this where you are looking?
Also what revision of er9x are you using (the number on the "Version menu" beside "SVN:")?

Mike.

OK Im using the v218 I having trouble getting my turnigy 9 ch receiver to bind with the transmitter its not binding only if I go back to the original 9x it binds fast its not working when I install back the 9xtreme board and also the numbers on the screen are not showing like on the youtube shows 1/11 2/11 3/11 and so on no page numbers

how do I use the voice recordings from the scan disk if the er9x version 218 don't have any way to pull the recordings out there is no selection on any of the screens it shows the scan disk is there and active but it does not have any selection to open for a voice recording

silversurfer48 wrote:OK Im using the v218 I having trouble getting my turnigy 9 ch receiver to bind with the transmitter its not binding only if I go back to the original 9x it binds fast its not working when I install back the 9xtreme board and also the numbers on the screen are not showing like on the youtube shows 1/11 2/11 3/11 and so on no page numbers

The RF module binding with the receiver has nothing to do with the radio itself.. Do you have servos connected to the receiver?
Also go to the main screen that shows some bars that represent the channels. Do the bars move when you move the sticks?
There are no more numbered pages in ersky9x. The videos you are watching are probably quite old.
Press the menu key long to open a popup menu that will allow you to select radio setup or model setup. Selecting for example model setup will take you to an index menu that lists all the menus. Select the one you need to edit.
All is organised now. And much easier to find..

João
EDIT: And please use punctuation when you write. A "." Is not so hard to type at the end of each sentence. That makes it easier for us to understand what you mean..

silversurfer48 wrote:how do I use the voice recordings from the scan disk if the er9x version 218 don't have any way to pull the recordings out there is no selection on any of the screens it shows the scan disk is there and active but it does not have any selection to open for a voice recording

Ok, I assume that by "Scan Disk" you mean "SD Card", right?
I can see you are not familiar with ersky9x. Do like this:
Go to www.er9x.com and download the "er9x manual"
Er9x is a light version of ersky9x but the basics are the same. Some options will be missing but the basic programming is the same and you will learn what the different options mean and what they do.
There is also a voice chapter that shows how to program voice events.

João

no page numbers Im looking for page numbers like in all the youtub

You won't find any more ersky9x firmware with page numbers, sorry..
As I said, those youtube videos might be too old.. There is openTX that still use page numbers as far as I know, but it doesn't support the 9xtreme board yet..

Please have a look at the manual to learn how to program your radio.

viewtopic.php?f=5&t=6473

Also, if you like videos, here is a Playlist with some I have made. There are a couple about voice programming.

https://www.youtube.com/playlist?list=P ... qcuIqJXhb9

João

I'm trying to get the voice to work on the TX its not working for me i have followed all the instruction on the er9x manual no progress Help!

Do you have any beeps (e.g. when pressing keys) or voice output at all (e.g. a welcome message)?

Please also give a specific example of what you have tried and what you expect to happen.

Mike.

Should TX protocol switch both be on? Because it looks has if this is the only way it looks if its binding but don't have proper settings for the RX quadcopter to test if its bind. I used the templete that was on one of rc openforums page. But dont know if its right with my 250 eachine racer can you please help me out with my problem

Are these "TX protocol switch" on the Tx module, if so what module is it?

Mike.

its RF9XV2 Turnigy native 2.4 ghz

I have no beeps and no sound. I have check speaker and it is connected right . I have smartie board extreme installed. I'm thinking maybe the scan disk is not properly loaded with voice but then still I'm not getting any beeps.

Please tell us exactly what equipment you have. If it's the stock Turnigy module, there are no switches on the module. So I'm guessing you are talking about Protocol in Model Settings in ErSky9x.

The FlySky/Turnigy module works with default settings.

silversurfer48 wrote:I have no beeps and no sound. I have check speaker and it is connected right . I have smartie board extreme installed. I'm thinking maybe the scan disk is not properly loaded with voice but then still I'm not getting any beeps.

Please go to Radio setup menu, AudioHaptic menu.. What setting you have selected in "Beeper"?
Also make sure the volume setting is not zero..

João

To avoid confusion, SD in this context stands for Secure Digital and has nothing to do with Scan Disk, which is a Microsoft program.

The SD card is always called the SD card.

I have did all that setting and still no beep or no voice and the sd does show active I open the tx and the speaker is connected Im not able to use eepe the only one thats allowing me to flash is skyeepe so I dont know if that has anything to do with that

I'm deducing the following.
1. You have a 9X radio fitted with a 9Xtreme upgrade board.
2. You have used eepskye to update the firmware on the 9Xtreme to revision 218.

Voice messages come from the SD card.
Beeps are generated directly, so should work even if the SD card is not working.

Please report what values you have in the "AudioHaptic" menu for:
1. Volume
2. Beeper.

For Volume I would like to see a value of 7 or greater.
For Beeper I would like to see "Norm".

Mike.

Yeah, I already asked that before but no valid answer..
silversurfer48, you must answer our questions or we are not able to help you. Remember that we can't see your radio, so you must tell us what settings you have..

João

Ok guys you got me on the right track thank you for your help