The postman arrived with :
1 hub , the vario. 1 t ° probe and fuel gauge
I changed firm TO ER9X r658 plugged in on my D8RII
RED AND BLACK : power ON SERVO plug
black and yellow status on GD and Rx line
and I can read on my th9x:
the t°: 2 measurements if two probes, in degree or fareneit
a height in meters or feets but not from 0 at startup (is it possible to calibrate: yes press menu long)i just discover it
how to convert this data in vario sound (rate of climb)?
and there is a page for the GPS but ,probe whas in back order...
how to use the gauge if possible ?
i found a reply :migrate to gruvin
i had hadded a A sensor: http://www.flytron.com/30-Array.html with a divider on ad 1
or a mpx 5010 on ad2 for air speed measurment
(in FRSKY ER9X its possible on One of the telemetry display screens shows the A1 and A2 values, together with their minimum and maximum values. If the type is set to A (for Amps), then the min value is replaced by mAh used. When this screen is displayed, and you press and hold the MENU key, the offset for the A1 and/or A2 will be calculated and the displayed value will then be 0. Press and hold the EXIT key should zero the mAh field as well as the timers
thank Mr BLANDFORD)with this mod measure on display can start from 0 i test asap !!!
jmi
frsky telemetry: how to
All mods related to the frsky telemetry series of the firmware
- JEANALTAYR
- Posts: 103
- Joined: Thu Dec 29, 2011 4:53 pm
- Country: -
- Location: Gd Toulouse FRANCE
Return to “FRSky Telemetry Mods”
Jump to
- OPENRC News & Information
- ↳ General Information & Rules
- ↳ Feedback
- General help and information
- ↳ Software
- ↳ Hardware
- ↳ General help (FrSky Taranis radio)
- Open Radio Control Transmitter Firmwares
- ↳ General model setup questions
- ↳ er9x / gruvin9x / th9 based firmwares
- ↳ Template Library
- ↳ Splash Screen Library
- ↳ Helicoptor Programming
- ↳ radioclone
- ↳ stock firmware (fly sky th9x)
- ↳ Template Library
- ↳ Sound Pack Library
- ↳ Edge TX
- ↳ openTx
- ↳ openTx for FrSky radios
- ↳ openTx model setup
- ↳ er9x
- ↳ er9x model setup
- ↳ ersky9xr
- ↳ erskyTx (was ersky9x)
- ↳ ersky9x model setup
- ↳ gruvin9x
- ↳ gruvin9x model setup
- ↳ th9x
- ↳ th9x model setup
- ↳ gv9x
- ↳ radioclone
- ↳ radioclone model setup
- ↳ tgy9xr
- ↳ tgy9xr model setup
- ↳ AR-T6
- ↳ other
- Desktop Software to Program Your Transmitter
- ↳ eePe
- ↳ companion9x
- ↳ eepSKYe
- Open Radio Control RF Systems & Hardware
- ↳ OpenLRS
- ↳ OpenLRSng
- ↳ OpenLRSng hardware
- Closed Source Radio Control RF Systems & Hardware
- ↳ Royal Way - Rlink UHF Long Range System
- Transmitter Hardware
- ↳ FlySky TH9X / Turnigy 9X / Eurgle 9X radio
- ↳ SMARTIEPARTS PROGRAMMER
- ↳ HARDWARE MODS & HACKS
- ↳ FRSky Telemetry Mods
- ↳ ArduPilot Mods
- ↳ Electronic Mods
- ↳ Hardware Mods
- ↳ Soldering, Hardware, Skills
- ↳ DSM2/DSMX Mods
- ↳ UPGRADE BOARDS
- ↳ sky9x upgrade board
- ↳ gruvin9x upgrade board
- ↳ 9Xtreme upgrade board
- ↳ RF MODULES
- ↳ The FRSKY Forum
- ↳ PROGRAMMERS
- ↳ FrSky Taranis radio
- ↳ FRSky Horus radio
- ↳ Turnigy 9XR PRO radio
- ↳ Orange DSM Telemetry module
- ↳ Turnigy 9XR radio
- ↳ PROGRAMMERS
- ↳ Other Radios
- ↳ Retro Radios
- Other OPEN Projects
- ↳ General RC Electronic Projects and Discussion
- ↳ OpenXVario - an open source vario supported by the open source firmwares!!
- ↳ Other Electronic Projects
- ↳ OpenFlightStab
- ↳ OpenLRSng
- ↳ 3D Printing
- Other Forums
- ↳ The Pickled Gnu (The Pub)
- ↳ FPV Projects
- ↳ Reviews
- ↳ Where to buy / Spares / Modules? Selling up?
- Links
- ↳ er9x on Google Code
- ↳ ersky9x on Github
- ↳ Gruvin9x on Google Code
- ↳ th9x on Google Code
- ↳ openTx on Google Code
- ↳ gv9x on Google Code
- ↳ radioclone on Sourceforge
- ↳ eePe on Google Code
- ↳ companion9x on Google Code
- ↳ 9X Guides
- ↳ openxvario