Mike, I am looking at building a Multiprotocol with a STM32 chip. The module uses a "SN74LVC2G00DCTR DUAL INPUT POSITIVE-NAND GATE". I have been told that this chip is needed because of the Taranis radio. I am planning to install this module as internal in my 9XT radio, and use COM2 for the telemetry.. My question is, do I need this chip with the 9XT??
Thank you
João
9Xtreme and Multiprotocol Module With STM chip
9Xtreme and Multiprotocol Module With STM chip
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17992
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: 9Xtreme and Multiprotocol Module With STM chip
If that is used to invert the telemetry output, then, for COM2 on a 9Xtreme, it is not needed. It would be needed for COM1.
You could fit it, then add a link to select the non-inverted or the inverted output.
Mike.
You could fit it, then add a link to select the non-inverted or the inverted output.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: 9Xtreme and Multiprotocol Module With STM chip
The problem is that I couldn't easily find the IC at a good price. As I said the module will be installed inside the radio, so it will use COM2 which according to you is fine without the inverter. COM1 is used by the module bay telemetry.
If really needed, I could use a transistor instead of that IC, right?
Thanks
João
If really needed, I could use a transistor instead of that IC, right?
Thanks
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9Xtreme and Multiprotocol Module With STM chip
Yes, the IC is used so that inversion can be enabled/disabled by software.
Re: 9Xtreme and Multiprotocol Module With STM chip
Yes, of course.. I understand.. Just wanted to know if it was really needed for the 9XT. It probably would, if I wanted to use the module in different radios, but as it will be installed internally, it is not needed, according to what Mike said..Kilrah wrote:Yes, the IC is used so that inversion can be enabled/disabled by software.
Thanks
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9Xtreme and Multiprotocol Module With STM chip
I was answering your question about replacing it with a transistor... already fogot you'd asked it?
Re: 9Xtreme and Multiprotocol Module With STM chip
Oh, ok, I misunderstood your post then, I do apologize.. Need some beer obvoiusly
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: 9Xtreme and Multiprotocol Module With STM chip
Is it really worth all the work, espacially with such cheap alternatives?jhsa wrote:Mike, I am looking at building a Multiprotocol with a STM32 chip. The module uses a "SN74LVC2G00DCTR DUAL INPUT POSITIVE-NAND GATE". I have been told that this chip is needed because of the Taranis radio. I am planning to install this module as internal in my 9XT radio, and use COM2 for the telemetry.. My question is, do I need this chip with the 9XT??
Thank you
João
2x - Turnigy 9X with 9xtreme board;
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
2x - Turnigy 9XRpro ;
Frsky Taranis & Taranis +;
Horus x10s;
Horus x12s;
Radiomaster TX16S Max mark II.
Re: 9Xtreme and Multiprotocol Module With STM chip
That's nRF only.
Re: 9Xtreme and Multiprotocol Module With STM chip
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW