My 9Xtreme Installation

birdman
Posts: 11
Joined: Thu Jun 02, 2016 2:28 am
Country: -

Re: My 9Xtreme Installation

Post by birdman » Thu Jun 02, 2016 10:37 pm

Where did you purchase the haptic vibration motors? The push buttons? Source and cost?
Thanks.

mmilan
Posts: 119
Joined: Fri Mar 23, 2012 12:16 am
Country: United States
Location: Holly, Mi

Re: My 9Xtreme Installation

Post by mmilan » Thu Jun 02, 2016 11:05 pm

"Unfortunately, 6BA screws are a bit hard to come by in the US. Do you think M2.5 or M3 screws will work? They are a bit easier to find. "

Another option that was worked well for me is to drill and tap for 3mm. This avoids splitting the fragile posts. Then the much easier to find 3mm bolts can be used.

Mike

User avatar
jhsa
Posts: 16675
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: My 9Xtreme Installation

Post by jhsa » Thu Jun 02, 2016 11:22 pm

birdman wrote:Where did you purchase the haptic vibration motors? The push buttons? Source and cost?
Thanks.
Haptic

http://www.ebay.com/itm/5PCS-DC-1-5-3V- ... Sw3ydV4-bG

Buttons

http://www.ebay.com/itm/20pcs-Tactile-P ... XQnXFRbB4G
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
Crusader
Posts: 28
Joined: Sun Apr 17, 2016 7:08 am
Country: Australia

Re: My 9Xtreme Installation

Post by Crusader » Fri Jun 03, 2016 5:41 am

Those haptic motors are better than the ones I tried first.

User avatar
jhsa
Posts: 16675
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: My 9Xtreme Installation

Post by jhsa » Fri Jun 03, 2016 8:20 am

They seem to be quite good.

João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW


birdman
Posts: 11
Joined: Thu Jun 02, 2016 2:28 am
Country: -

Re: My 9Xtreme Installation

Post by birdman » Fri Jun 03, 2016 5:31 pm

Thanks for the info for the vibration motors and oush buttons. Already on order. Just a few more questions about materials.
1. Where to order the copper clad PC boards for the pushbuttons?
2. What is the diode specs for reverse polarity expansion?
3. Where to order connectors for 9Extreme pc board if one doesnt order the Teranis gimbals?
Thanks.

User avatar
jhsa
Posts: 16675
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: My 9Xtreme Installation

Post by jhsa » Fri Jun 03, 2016 6:42 pm

birdman wrote:Thanks for the info for the vibration motors and oush buttons. Already on order. Just a few more questions about materials.
1. Where to order the copper clad PC boards for the pushbuttons?
Bought them from an online shop here in germany. Reichelt
2. What is the diode specs for reverse polarity expansion?
Diodes datasheets attached to this post.
3. Where to order connectors for 9Extreme pc board if one doesnt order the Teranis gimbals?
If you don't want to replace the 9x gimbals you just connect the stock connectors to the 9Xtreme, Please refer to the 9xtreme website for detailed instasllation guide..

João
Attachments
1n4001.pdf
(76.93 KiB) Downloaded 30 times
1N4148_to_1N916B.pdf
(48.4 KiB) Downloaded 20 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

birdman
Posts: 11
Joined: Thu Jun 02, 2016 2:28 am
Country: -

Re: My 9Xtreme Installation

Post by birdman » Fri Jun 03, 2016 11:38 pm

Thanks again for the info. Again one more question.

For the reverse polarity protection diode shown in your photo on the first page of this thread (circuit board FS-TH9-FRONT) what are its specs?
Thanks.

User avatar
jhsa
Posts: 16675
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: My 9Xtreme Installation

Post by jhsa » Fri Jun 03, 2016 11:59 pm

I used this one.. Please see attached..
I have just realized that i didn't say which diode I used..
Will update the first post tomorrow

Thanks

João
Attachments
MBRA340T3G_40V_3A.pdf
(54.82 KiB) Downloaded 40 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

birdman
Posts: 11
Joined: Thu Jun 02, 2016 2:28 am
Country: -

Re: My 9Xtreme Installation

Post by birdman » Sat Jun 04, 2016 5:02 pm

Hello Joao,
From my previous note I as referring to the 9 pin connectors that are connected to the 9x main board allowing access to XT1...EXT8 for switches, pushbuttons & sliders. Where do you get the 9 pin connectors if you don't use Tyrannis gimbals and cut off its 9 pin connectors? Are these just Molex type of connectors? That can be ordered from Molex suppliers? Thanks.

lancaster
Posts: 168
Joined: Thu Jun 12, 2014 10:28 pm
Country: United Kingdom

Re: My 9Xtreme Installation

Post by lancaster » Mon Jun 06, 2016 8:46 am

Hi Birdman

I attach some information about the 9 pin connectors I used

Thanks to Joao for this

regards
Hans
Attachments
9 pin jst connector.docx
(131.75 KiB) Downloaded 63 times

birdman
Posts: 11
Joined: Thu Jun 02, 2016 2:28 am
Country: -

Re: My 9Xtreme Installation

Post by birdman » Sat Jun 25, 2016 12:13 am

Hello Joao,
From your note on June 4th concerning the protection Schottky diode what diode did you order?

There are two types: MBA340T3 or MBA340T3G?

Thanks

User avatar
jhsa
Posts: 16675
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: My 9Xtreme Installation

Post by jhsa » Sat Jun 25, 2016 12:29 am

Mine is the MBRA340T3G

João
Attachments
MBRA340T3G_40V_3A.pdf
(54.82 KiB) Downloaded 31 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
OctavioS
Posts: 528
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: My 9Xtreme Installation

Post by OctavioS » Fri Aug 26, 2016 8:53 pm

Hi i have done this mod and would like to know if its safe to use a djt module like that. With this, the DJT will have a connection to the 5th pin and simultaneously to the back plug for the telemetry (rx/tx).
photo_1453925614671.jpg
photo_1453925614671.jpg (43.09 KiB) Viewed 1210 times
Any precise help would be apreciated.
thx
3 x - 9X TX with 9xtreme board, running ersky9x;
Turnigy 9XRpro running ersky9x;
Frsky Taranis & Taranis plus running opentx.
Too much radios? Horus is next. :D

"Sometimes you just have to take a leap and build your wings on the way down."

User avatar
Kilrah
Posts: 9094
Joined: Sat Feb 18, 2012 6:56 pm
Country: Switzerland

Re: My 9Xtreme Installation

Post by Kilrah » Fri Aug 26, 2016 9:32 pm

Any precise info would be appreciated.

There's typically an inverter to wire in there. If you refer to a mod that doesn't need one, say so and link to it.

User avatar
MikeB
9x Developer
Posts: 14474
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset

Re: My 9Xtreme Installation

Post by MikeB » Fri Aug 26, 2016 9:49 pm

You may wire the telemetry Tx signal from the DJT directly to the 9Xtreme (no inverter needed for the 9Xtreme).
The 9Xtreme has a 1K resistor in the telemetry signal to limit current flow and a clamp diode to handle the negative voltage from the RS232 signal from the DJT.
Assuming the black and white wires are plugged in to the rear of the DJT, this is correct.
With the black wire also connected to pin 5 (bottom pin) of the module connector, this would allow an XJT to be plugged in and work correctly as well.

Mike.
ersky9x/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
bob195558
Posts: 1559
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: My 9Xtreme Installation

Post by bob195558 » Fri Aug 26, 2016 10:21 pm

RADIOS: ErSky9x on Taranis, ErSky9x on Sky9x, ErSky9x on 9Xtreme,
Er9x-FrSky on 9x-Radio with Smartieparts upgrade Programmer Board and 9x-TelemetrEZ Board.
Some help info here: (http://openrcforums.com/forum/viewtopic.php?f=95&t=7182).
Bob B.

User avatar
OctavioS
Posts: 528
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: My 9Xtreme Installation

Post by OctavioS » Fri Aug 26, 2016 11:41 pm

OK, thank you all for the replies. Thats what i wanted to hear. Since there is no problem than all is perfect.
3 x - 9X TX with 9xtreme board, running ersky9x;
Turnigy 9XRpro running ersky9x;
Frsky Taranis & Taranis plus running opentx.
Too much radios? Horus is next. :D

"Sometimes you just have to take a leap and build your wings on the way down."

User avatar
OctavioS
Posts: 528
Joined: Sun Aug 17, 2014 11:54 pm
Country: Portugal
Location: Madeira

Re: My 9Xtreme Installation

Post by OctavioS » Fri Aug 26, 2016 11:43 pm

Kilrah wrote:Any precise info would be appreciated.

There's typically an inverter to wire in there. If you refer to a mod that doesn't need one, say so and link to it.
I thought i was clear enough.
3 x - 9X TX with 9xtreme board, running ersky9x;
Turnigy 9XRpro running ersky9x;
Frsky Taranis & Taranis plus running opentx.
Too much radios? Horus is next. :D

"Sometimes you just have to take a leap and build your wings on the way down."

Post Reply

Return to “9Xtreme upgrade board”

Who is online

Users browsing this forum: No registered users and 4 guests