Frsky xjt bind not working
Frsky xjt bind not working
So I have the 9XR Pro with the xjt module that I just got and once I set protocol to PXX trying to use the bind option in the radio firmware it doesn't work it shows binding and I hold the AFS button on the receiver down power it up red light starts flashing turn everything off remove jumpers turn everything back on and there's no link no green light shown
- MikeB
- 9x Developer
- Posts: 17992
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Frsky xjt bind not working
What receiver are you using?
If it is a 'X' receiver, please try turning the Rx on holding the FS button down, then select the BIND option on the radio. The red LED on the Rx should then start flashing indicating the bind is complete. Press EXIT on the radio and power the Rx off and on. What do the LEDs on the Rx do now?
Mike.
If it is a 'X' receiver, please try turning the Rx on holding the FS button down, then select the BIND option on the radio. The red LED on the Rx should then start flashing indicating the bind is complete. Press EXIT on the radio and power the Rx off and on. What do the LEDs on the Rx do now?
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Frsky xjt bind not working
OK so I am supposed to turn on receiver first holding the f/s then press bind on radio? I am using X6R RX's.
I was pressing bind first and then turning of RX with f/s held down.
One question as well
Am i correct that if i have 2 models turned on that the one that is selected in my radio will be the one that the transmitter links to correct?
I was pressing bind first and then turning of RX with f/s held down.
One question as well
Am i correct that if i have 2 models turned on that the one that is selected in my radio will be the one that the transmitter links to correct?
- MikeB
- 9x Developer
- Posts: 17992
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Frsky xjt bind not working
You should only have ONE receiver trying to bind at a time. By selecting a different RxNum value for each model/receiver, then, after binding that sets this value in the receiver, only that one receiver will then respond to the Tx.
By powering the Rx first, you will see clearly if the red LED starts flashing after binding. The red LED flashes slower in normal operation if it is not receiving a signal. You may not recognise these different rates of flashing until you have seen them both.
Mike.
By powering the Rx first, you will see clearly if the red LED starts flashing after binding. The red LED flashes slower in normal operation if it is not receiving a signal. You may not recognise these different rates of flashing until you have seen them both.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Frsky xjt bind not working
ok cool mike I will attempt it again tonight and report back. I get off work in a little over and hour so.
Re: Frsky xjt bind not working
Hey Mike that worked great doing it in that order. I got my replacement from HK tonight as well. So I hooked old one up and saved settings then burned them onto the replacement. Gone are the days of flying a model with the wrong model selected in the radio!! so freaking COOL!
The only other thing I got going on is to get telemetry to display I have to go into model setup--->telemetry->page 3 and change invert com 1 from off to on back to off. Then telemetry works just fine. any ideas?
The only other thing I got going on is to get telemetry to display I have to go into model setup--->telemetry->page 3 and change invert com 1 from off to on back to off. Then telemetry works just fine. any ideas?
- MikeB
- 9x Developer
- Posts: 17992
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Frsky xjt bind not working
Check what is happening with your real time clock.
Is it running?
Have you set the date/time?
Does it then keep the time when you switch the radio off?
The control signal for the telemetry inverter is controlled by the RTC chip. If it isn't running, the inverter control doesn't work.
Mike.
Is it running?
Have you set the date/time?
Does it then keep the time when you switch the radio off?
The control signal for the telemetry inverter is controlled by the RTC chip. If it isn't running, the inverter control doesn't work.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Frsky xjt bind not working
Ahh stupid me, I didn't set the time and date in the new radio.......
Re: Frsky xjt bind not working
Where do you find bind in R219?
- MikeB
- 9x Developer
- Posts: 17992
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Frsky xjt bind not working
For the XJT, it is in the Protocol menu. You need to set the protocol to "XJT" (renamed from "PXX") before the Bind option appears.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!