setting flysky9x with dm9(binding issues)
setting flysky9x with dm9(binding issues)
Hi there i recently got my hands on a dm9 module to use with my flysky 9x but i can't get it to bind with my ar9000 receivers.
i think the problem lies with me unable to get the transmitter module into bind mode as the dm9 light remains solid orange instead or flashing orange.
i have tried the following settings:
1)
PPM
CH1-8
22.5ms
400u
+ and -
2) DSM2
RxNum 1
DSM2only
1st Chan 1
Range Check
and i have also installed the smartie parts board to flash the ersky9x firmware.
do anyone know how to setup the transmitter for the dm9 module to work or is there any other mods that i am required to do before i will be able to use the dm9 module on my flysky9x.
i think the problem lies with me unable to get the transmitter module into bind mode as the dm9 light remains solid orange instead or flashing orange.
i have tried the following settings:
1)
PPM
CH1-8
22.5ms
400u
+ and -
2) DSM2
RxNum 1
DSM2only
1st Chan 1
Range Check
and i have also installed the smartie parts board to flash the ersky9x firmware.
do anyone know how to setup the transmitter for the dm9 module to work or is there any other mods that i am required to do before i will be able to use the dm9 module on my flysky9x.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: setting flysky9x with dm9(binding issues)
This may be some help: (viewtopic.php?f=96&t=9142&p=118300&hili ... le#p118273).
I think the settings works the same way with Taranis /opentx and 9Xtreme / ErSky9x firmware.
Bob B.
I think the settings works the same way with Taranis /opentx and 9Xtreme / ErSky9x firmware.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: setting flysky9x with dm9(binding issues)
I was following that link instructions but i can't seem to get it to work,i have only change the settings in the protocol menu not sure if there are other setting to change.bob195558 wrote: I think the settings works the same way with Taranis /opentx and 9Xtreme / ErSky9x firmware.
Bob B.
Re: setting flysky9x with dm9(binding issues)
i re-read the page is there a need to change the mixer? if yes then i don't get the settings of the mixer in relation to ersky9x as there is no S1,S2 and etc. but a look up on google seems to not help at all as it doesn't show any differencebob195558 wrote:This may be some help: (viewtopic.php?f=96&t=9142&p=118300&hili ... le#p118273).
I think the settings works the same way with Taranis /opentx and 9Xtreme / ErSky9x firmware.
Bob B.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: setting flysky9x with dm9(binding issues)
With the Taranis S1, S2, LS and RS are pots, FlySky 9x radio labels them as P1, P2 and P3.
I believe these Mixe setting have nothing to do with your problem.
What version of radio firmware and what modes (edit) mods are done on your 9x radio ?
Bob B.
I believe these Mixe setting have nothing to do with your problem.
What version of radio firmware and what modes (edit) mods are done on your 9x radio ?
Bob B.
Last edited by bob195558 on Wed Sep 14, 2016 11:30 am, edited 1 time in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: setting flysky9x with dm9(binding issues)
For modesbob195558 wrote:With the Taranis S1, S2, LS and RS are pots, FlySky 9x radio labels them as P1, P2 and P3.
I believe these Mixe setting have nothing to do with your problem.
What version of radio firmware and what modes are done on your 9x radio ?
Bob B.
i have only done 2
1)install the smartie parts 9xtreme board
2) the battery reverse polarity protection
as for radio firmware i am using ERSKY9X (revision 218) that comes with the 9xtreme board.
are there other mods i have to make for the dm9 module?
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: setting flysky9x with dm9(binding issues)
You should update your ersky9x9XT_rom firmware from the one that comes on the 9Xtreme Board,albusrice wrote: as for radio firmware i am using ERSKY9X (revision 218) that comes with the 9xtreme board.
are there other mods i have to make for the dm9 module?
Your can find it here: (http://www.er9x.com/).
Also here is a directory of information about 9Xtreme Board and using erSky9x and eepSkye: (viewtopic.php?f=95&t=7182).
I do not know if there is a mod needed for the dm9 module, maybe someone knows better with using dm9 module, who could help.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: setting flysky9x with dm9(binding issues)
do u know of any mods for me to switch to opentx as it may help with the binding issue. since most instructions is for opentxbob195558 wrote:You should update your ersky9x9XT_rom firmware from the one that comes on the 9Xtreme Board,albusrice wrote: as for radio firmware i am using ERSKY9X (revision 218) that comes with the 9xtreme board.
are there other mods i have to make for the dm9 module?
Your can find it here: (http://www.er9x.com/).
Also here is a directory of information about 9Xtreme Board and using erSky9x and eepSkye: (viewtopic.php?f=95&t=7182).
I do not know if there is a mod needed for the dm9 module, maybe someone knows better with using dm9 module, who could help.
Bob B.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: setting flysky9x with dm9(binding issues)
I don't believe openTx has been ported for the 9Xtreme board.
Do you have other Tx modules that are working correctly with the 9Xtreme? (To check the 9Xtreme is outputting a PPM signal correctly).
Mike.
Do you have other Tx modules that are working correctly with the 9Xtreme? (To check the 9Xtreme is outputting a PPM signal correctly).
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: setting flysky9x with dm9(binding issues)
yea if i am using the module that comes with the transmitter it is working.MikeB wrote:I don't believe openTx has been ported for the 9Xtreme board.
Do you have other Tx modules that are working correctly with the 9Xtreme? (To check the 9Xtreme is outputting a PPM signal correctly).
Mike.
Re: setting flysky9x with dm9(binding issues)
You need to test your DM9 with another radio, or did you already do it?
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: setting flysky9x with dm9(binding issues)
i can't do that unfortunately... i don't have another radiojhsa wrote:You need to test your DM9 with another radio, or did you already do it?
João
Re: setting flysky9x with dm9(binding issues)
Well, you need to find out somehow if your module is working
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: setting flysky9x with dm9(binding issues)
I've just remembered the 9XR-PRO module pins are shorter than those of other radios. It may be the the PPM pin (top pin) is not making contact in the module.
Measurements on some radios:
9XR-PRO - 10.5mm from rear of module bay.
9X - 11.5mm
Taranis 14mm
Mike.
Measurements on some radios:
9XR-PRO - 10.5mm from rear of module bay.
9X - 11.5mm
Taranis 14mm
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: setting flysky9x with dm9(binding issues)
I forget too, that a new person may, has not yet done the module bay mod.
With the FlySky and Turnigy 9x radios the plastic around the 5 module pins needs to be removed to look like this: Bob B.
With the FlySky and Turnigy 9x radios the plastic around the 5 module pins needs to be removed to look like this: Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: setting flysky9x with dm9(binding issues)
Hmm.. I was thinking that might be possible but if the module is powered up will there be a problem with the ppm pin contact?bob195558 wrote:I forget too, that a new person may, has not yet done the module bay mod.
With the FlySky and Turnigy 9x radios the plastic around the 5 module pins needs to be removed to look like this:
9x module Bay.jpg
Bob B.
Re: setting flysky9x with dm9(binding issues)
Could be yes, the pins are just about long enough so one might touch and the other not.
That plastic sleeve must absolutely be removed when using third party modules.
That plastic sleeve must absolutely be removed when using third party modules.
Re: setting flysky9x with dm9(binding issues)
The JR standard need the pins protrude by 1/2" from the back of the module case.
Re: setting flysky9x with dm9(binding issues)
so how do u remove it? by jus cutting it out with a pen knife or are they better ways to go abt doing it?
Re: setting flysky9x with dm9(binding issues)
it is easier to cut/grind it if you lift the back PCB. You just need to remove a few screws.
No chance of damaging the pins, and you have more room to work.
João
No chance of damaging the pins, and you have more room to work.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: setting flysky9x with dm9(binding issues)
After removing my 5 pin board, I just grabbed, crushed and twisted off the plastic with a pair of pliers.
The standoff that needs to be removed happens to have a seam around it and very little "clean-up" is needed after ripping it off.
The standoff that needs to be removed happens to have a seam around it and very little "clean-up" is needed after ripping it off.
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: setting flysky9x with dm9(binding issues)
Open up your 9x radio and remover the PCB green back board.
You can then use a Dremel to mill the plastic away.
Some people have used different ways to remove the plastic pin support. Bob B.
You can then use a Dremel to mill the plastic away.
Some people have used different ways to remove the plastic pin support. Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
Re: setting flysky9x with dm9(binding issues)
Hi here i did the mod as instructed above but i am still only getting a solid light and not a flashing one
Re: setting flysky9x with dm9(binding issues)
Ok, you will need to do a test to see if your radio is outputting PPM on pin 1.
Please go to Radio Setup/Trainer menu. Now connect a trainer cable to the trainer port. any audio Jack to jack mono or stereo cable will work.
VERY IMPORTANT, Isolate all pins in the module bay except pin 1, so you don't have any short circuits between pins.. That could kill your radio. Don't skip this step.. Do this while the radio is still OFF, of course...
Now touch the tip of the other jack plug on pin 1. if you move the sticks now, you should see the values at the bottom of the trainer menu moving. Please report back.
João
Please go to Radio Setup/Trainer menu. Now connect a trainer cable to the trainer port. any audio Jack to jack mono or stereo cable will work.
VERY IMPORTANT, Isolate all pins in the module bay except pin 1, so you don't have any short circuits between pins.. That could kill your radio. Don't skip this step.. Do this while the radio is still OFF, of course...
Now touch the tip of the other jack plug on pin 1. if you move the sticks now, you should see the values at the bottom of the trainer menu moving. Please report back.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: setting flysky9x with dm9(binding issues)
by isolating do i remove the module?jhsa wrote:Ok, you will need to do a test to see if your radio is outputting PPM on pin 1.
Please go to Radio Setup/Trainer menu. Now connect a trainer cable to the trainer port. any audio Jack to jack mono or stereo cable will work.
VERY IMPORTANT, Isolate all pins in the module bay except pin 1, so you don't have any short circuits between pins.. That could kill your radio. Don't skip this step.. Do this while the radio is still OFF, of course...
Now touch the tip of the other jack plug on pin 1. if you move the sticks now, you should see the values at the bottom of the trainer menu moving. Please report back.
João
pretty sure i am doing it wrongly as i am not getting any response
Re: setting flysky9x with dm9(binding issues)
Yes, remove the module and protect the other pins with something (not metal of course) so you don't short them when you touch pin 1 with the tip of the jack plug.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: setting flysky9x with dm9(binding issues)
Sry for the late reply just managed to get a proper audio jack.jhsa wrote:Yes, remove the module and protect the other pins with something (not metal of course) so you don't short them when you touch pin 1 with the tip of the jack plug.
João
Not sure if I am doing it right but this is the output I am getting
Re: setting flysky9x with dm9(binding issues)
Turn the radio ON before, and only then insert the jack plug. Then go to the trainer menu. Now touch the tip of the other jack plug on pin 1 in the module bay.
Do the numbers at the bottom of the trainer screen move?
João
Do the numbers at the bottom of the trainer screen move?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
Re: setting flysky9x with dm9(binding issues)
no it doesn't movejhsa wrote:Turn the radio ON before, and only then insert the jack plug. Then go to the trainer menu. Now touch the tip of the other jack plug on pin 1 in the module bay.
Do the numbers at the bottom of the trainer screen move?
João
Re: setting flysky9x with dm9(binding issues)
go to the main screen that show be output channels as bars. Do the bars move when you move the sticks?
Do you have the protocol set to PPM in the protocol menu?
Did you ever insert or remove the RF module while the radio was ON?
João
Do you have the protocol set to PPM in the protocol menu?
Did you ever insert or remove the RF module while the radio was ON?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW