Assign ID to exponential travel profiles

ersky9xr is the port of the er9x firmware to the 9XRPRO radio.
Post Reply
User avatar
iFeghali
Posts: 46
Joined: Sun Jul 29, 2018 2:19 am
Country: Brazil

Assign ID to exponential travel profiles

Post by iFeghali »

Hello

Is there a way to assign the 3 position switch “ID” to exponential travel profiles in the following way:

ID- > LOW
ID > MID
ID+ > HIGH

?


Enviado do meu iPhone usando Tapatalk

User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Assign ID to exponential travel profiles

Post by jhsa »

You mean something like a triple rate but with Expo only?

João?
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
iFeghali
Posts: 46
Joined: Sun Jul 29, 2018 2:19 am
Country: Brazil

Re: Assign ID to exponential travel profiles

Post by iFeghali »

jhsa wrote:You mean something like a triple rate but with Expo only?

João?
Nope. I know I can set set 3 profiles for EXPO for each channel. So I can have a LOW EXPO, MID EXPO and HIGH EXPO for each channel. I can then assign TWO buttons to switch between those 3 profiles. If I use two normal switches they give me 4 different combinations but we have only 3 profiles, so one of them gets repeated and it’s confusing. That’s why I want to use a single 3 position switch which would make a lot more sense for me.


Enviado do meu iPhone usando Tapatalk
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Assign ID to exponential travel profiles

Post by MikeB »

Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Assign ID to exponential travel profiles

Post by jhsa »

This is why I asked if he wanted the triple rate. I didn't understand his question :)
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW

User avatar
iFeghali
Posts: 46
Joined: Sun Jul 29, 2018 2:19 am
Country: Brazil

Re: Assign ID to exponential travel profiles

Post by iFeghali »

MikeB wrote:Set DrSw1 to !ID^ (!ID0) and DrSw2 to IDv (ID2).
With the swith up you get high rate, in the centre you get mid rate and down gives you low rate.

Mike
That’s the first thing I tried mike, but unfortunately it didn’t work (or I’m doing it wrong). Doing as you said I get MID at the top and HIGH at middle and bottom.

Image


Enviado do meu iPhone usando Tapatalk
User avatar
MikeB
9x Developer
Posts: 17990
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: Assign ID to exponential travel profiles

Post by MikeB »

DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.

Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
User avatar
iFeghali
Posts: 46
Joined: Sun Jul 29, 2018 2:19 am
Country: Brazil

Re: Assign ID to exponential travel profiles

Post by iFeghali »

MikeB wrote:DrSw1 needs to be !ID^ (that is NOT ID^). When editing the switch value go DOWN to get the NOT switch values.

Mike
Thank you very much. Works like a charm :)


Enviado do meu iPhone usando Tapatalk
User avatar
jhsa
Posts: 19480
Joined: Tue Dec 27, 2011 5:13 pm
Country: Germany

Re: Assign ID to exponential travel profiles

Post by jhsa »

Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)

In my opinion it will work better. I have just tried in Eepskye :)
By the way, triple rates are explained on the Er9x manual, page 42 and 43.

João
Attachments
ER9x_Manual_2015-v01.pdf
(2.08 MiB) Downloaded 250 times
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9

Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
User avatar
iFeghali
Posts: 46
Joined: Sun Jul 29, 2018 2:19 am
Country: Brazil

Re: Assign ID to exponential travel profiles

Post by iFeghali »

jhsa wrote:Try:
DrSw1 set as !IDv (!ID2)
DrSw2 set as !ID^ (!ID1)

In my opinion it will work better. I have just tried in Eepskye :)
By the way, triple rates are explained on the Er9x manual, page 42 and 43.

João
Thanks. It’s clear now. For anyone interested that’s the relevant part:


Hi is DrSw1 OFF (DrSw2 doesn't matter)
Mid is DrSw1 ON, DrSw2 OFF
Lo is DrSw1 ON, DrSw2 ON


Enviado do meu iPhone usando Tapatalk

Post Reply

Return to “ersky9xr”