Switch arm with DJI Naza M lite
-
- Posts: 47
- Joined: Sat Dec 09, 2017 4:31 am
- Country: -
- Location: Sahuarita Arizona
Switch arm with DJI Naza M lite
Hi all,
My brother has a DJI Naza M Lite, running the latest version of Ersky9x on 9xrPro. He wants to arm the quadcopter using a switch instead of the stick arming. Tried to follow this video but it was for OpenTx: https://www.youtube.com/watch?v=fxIDxb-aDvk
Tried as best as we could to do the set up and try to figure out what is what from opentx to ersky9x. Also looked in the manual for Er9x and tried to follow the logic for 16. Automatic Landing Gear and Canopy on page 82 of the manual, did not work. At a loss as what to do next. Any help would be appreciated.
My brother has a DJI Naza M Lite, running the latest version of Ersky9x on 9xrPro. He wants to arm the quadcopter using a switch instead of the stick arming. Tried to follow this video but it was for OpenTx: https://www.youtube.com/watch?v=fxIDxb-aDvk
Tried as best as we could to do the set up and try to figure out what is what from opentx to ersky9x. Also looked in the manual for Er9x and tried to follow the logic for 16. Automatic Landing Gear and Canopy on page 82 of the manual, did not work. At a loss as what to do next. Any help would be appreciated.
When I'm not flying I'm dreaming of flying, when I'm not dreaming of flying.....I'm asleep
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Switch arm with DJI Naza M lite
Instead of "channel override", ersky9x uses the "safety switches". Set up a safety switch on each of channels 1-4 using the required logical switch as the control and set the required output value.
The set up for the logical switch should be the same.
Mike
The set up for the logical switch should be the same.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Switch arm with DJI Naza M lite
I did/do this with my (ersky9x) Taranis, I will see if I can find where I have it posted.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Switch arm with DJI Naza M lite
Found this not sure it has what you need:
(http://openrcforums.com/forum/viewtopic ... te#p116428)
(http://openrcforums.com/forum/viewtopic ... te#p116428)
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Switch arm with DJI Naza M lite
Some more info here: (http://openrcforums.com/forum/viewtopic ... te#p114948)
With the Taranis the switch I use is labeled "SF"
and I am not sure I am using it to arm,
but I am using as a safety switch on CH3 for the Throttle. Sorry I did not remember correctly, I am not arming with a switch.
With the Taranis the switch I use is labeled "SF"
and I am not sure I am using it to arm,
but I am using as a safety switch on CH3 for the Throttle. Sorry I did not remember correctly, I am not arming with a switch.
Last edited by bob195558 on Sat Jun 23, 2018 5:09 pm, edited 3 times in total.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
-
- Posts: 47
- Joined: Sat Dec 09, 2017 4:31 am
- Country: -
- Location: Sahuarita Arizona
Re: Switch arm with DJI Naza M lite
Thanks for your input, we will try these out and post results back here when done.
When I'm not flying I'm dreaming of flying, when I'm not dreaming of flying.....I'm asleep
-
- Posts: 47
- Joined: Sat Dec 09, 2017 4:31 am
- Country: -
- Location: Sahuarita Arizona
Re: Switch arm with DJI Naza M lite
OkEdwardMcRichy wrote: ↑Sat Jun 23, 2018 1:04 pm Thanks for your input, we will try these out and post results back here when done.
We tried the safety switch out but are unsure of how exactly to do it. I've attached some photos of the screens for in the mixer, logical switch and safety switch. I read through the er9x manual and this is the best we could figure out. Didn't work, probably because we are not doing it correctly but if anybody has an idea of what we need to change, your assistance would be helpful.
Bob, there was a lot of information to sift through at the links you provided, didn't see any info that would help, but again lot of stuff to look through.
When I'm not flying I'm dreaming of flying, when I'm not dreaming of flying.....I'm asleep
Re: Switch arm with DJI Naza M lite
Change the logic switch to "v<val"
Reinhard
Reinhard
-
- Posts: 47
- Joined: Sat Dec 09, 2017 4:31 am
- Country: -
- Location: Sahuarita Arizona
Re: Switch arm with DJI Naza M lite
My brother a I are at our wits end. We can't figure out the switch arming in Ersky9x. We've looked at the links supplied in this thread and still can't figure it out. Below are some photos of what the settings were. We can't get the quad to arm by switch. I've read the whole section in the Er9x manual on logic switches and safety switches, maybe there is something I'm not understanding because we just can't get it to work. Does anybody have any other thoughts?
In the safety switches screen do the channels there = the channel numbers in the mixer, ex. ch2 in safety switches is ch2 in mixer? Do i need to get rid of the THR on all the channels in safety switches except for channel 3 (AETR)?
Should we lower the value on each channel in safety switches for example we have extended limits on should we change the -125 to -100?
We can't find any information on the DJI forum
thanks for any input that helps.
When I'm not flying I'm dreaming of flying, when I'm not dreaming of flying.....I'm asleep
Re: Switch arm with DJI Naza M lite
Ok, give me a couple hours and I will try to help you.. I will have to read the posts above to find out what is required. But I already saw some stuff on your photos that doesn't look quite right.
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Switch arm with DJI Naza M lite
L1 will never be true as the Thr stick doesn't go below -100%, Try changing the -125 to -98.
Mike
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Switch arm with DJI Naza M lite
Try:
Logical switches:
L1 v<val -96 TRN (use GEA if you try in eepskye, and TRN switch if you are trying this on the radio)
Safety Switches:
CH1 S L1 -100
CH2 S L1 -100
CH3 S L1 -100
CH4 S L1 -100
What is each channel supposed to do while arming and disarming?? Please note that different flight controllers might need different procedures. Some even have different combinations for arming and disarming..
João
Logical switches:
L1 v<val -96 TRN (use GEA if you try in eepskye, and TRN switch if you are trying this on the radio)
Safety Switches:
CH1 S L1 -100
CH2 S L1 -100
CH3 S L1 -100
CH4 S L1 -100
What is each channel supposed to do while arming and disarming?? Please note that different flight controllers might need different procedures. Some even have different combinations for arming and disarming..
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW