Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
- SilentException
- Posts: 3
- Joined: Mon Jan 01, 2018 5:56 pm
- Country: Croatia
- Location: Croatia/Slovenia
- Contact:
Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Hi,
I tried to use Turnigy 9XR Pro with latest available R221g1 to update firmware on FrSky R-XSR receiver, following the steps from the PDF on this forum. Because of the 12V Vbat on the module pin, I used external power with GND and Vin connected (Vin was with the switch in-between, as per instructions).
GND was also connected to the module pin. The S.Port was connected to the bottom module pin as well.
After seeing searching for device during procedure, I turned on the switch to power on the receiver and the firmware update started but stopped immediately on 0087 of XXXX. I left it for couple of minutes but it didn't move at all so I aborted the procedure. The RX was "broken" at this point. After powering it on, only the green LED was lit. I tried to repeat the procedure couple of times but with same results - stop on 0087 and nothing further. For some reason, after one failed update the RX started to have different LED pattern after powering it on -> brief green LED flash followed with couple of seconds of blue LED over and over again, like it was rebooting itself all the time.
Today I used friends Taranis 9XD to update that same receiver, similar connections without external power because the Taranis had 7V battery. The firmware update was executed without any issues and the receiver is thankfully in working state now.
Is there any known problem updating the R-XSR in 9XR radio?
I tried to use Turnigy 9XR Pro with latest available R221g1 to update firmware on FrSky R-XSR receiver, following the steps from the PDF on this forum. Because of the 12V Vbat on the module pin, I used external power with GND and Vin connected (Vin was with the switch in-between, as per instructions).
GND was also connected to the module pin. The S.Port was connected to the bottom module pin as well.
After seeing searching for device during procedure, I turned on the switch to power on the receiver and the firmware update started but stopped immediately on 0087 of XXXX. I left it for couple of minutes but it didn't move at all so I aborted the procedure. The RX was "broken" at this point. After powering it on, only the green LED was lit. I tried to repeat the procedure couple of times but with same results - stop on 0087 and nothing further. For some reason, after one failed update the RX started to have different LED pattern after powering it on -> brief green LED flash followed with couple of seconds of blue LED over and over again, like it was rebooting itself all the time.
Today I used friends Taranis 9XD to update that same receiver, similar connections without external power because the Taranis had 7V battery. The firmware update was executed without any issues and the receiver is thankfully in working state now.
Is there any known problem updating the R-XSR in 9XR radio?
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
No known problems, it has been working for me.
Mike.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- SilentException
- Posts: 3
- Joined: Mon Jan 01, 2018 5:56 pm
- Country: Croatia
- Location: Croatia/Slovenia
- Contact:
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Hey Mike, thanks for the reply. You tested with R-XSR receiver?
Since Taranis had no problems at all doing the upgrade, the wiring was same/similar (without external power), I could only assume it was 9RX Pro that was causing issue.
Since Taranis had no problems at all doing the upgrade, the wiring was same/similar (without external power), I could only assume it was 9RX Pro that was causing issue.
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
No, I don't have a R-XSR receiver, but it updates like any other SPort device, and I have been updating other devices using the 'PRO.
An odd problem you have seen, since I wrote the update firmware originally, and it was ported to openTx later.
Could be a problem reading the firmware file from the SD card, I guess you use a different SD card in the Taranis!
Mike.
An odd problem you have seen, since I wrote the update firmware originally, and it was ported to openTx later.
Could be a problem reading the firmware file from the SD card, I guess you use a different SD card in the Taranis!
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
- SilentException
- Posts: 3
- Joined: Mon Jan 01, 2018 5:56 pm
- Country: Croatia
- Location: Croatia/Slovenia
- Contact:
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Interesting thought about SD card. In 9RX Pro I use the SD card that came with the TX. On the PC I have no issue reading (copying) the file though.
I can always try and reflash the same firmware again, using different SD card to test the hypothesis, I suppose the RX wouldn't mind.
I can always try and reflash the same firmware again, using different SD card to test the hypothesis, I suppose the RX wouldn't mind.
-
- Posts: 1
- Joined: Tue Apr 17, 2018 8:51 pm
- Country: -
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Hi, I also had the exact same problem. Update got to 0087 of 4000 and freeze. I kept trying different firmware for the r-xsr and every one would stop in the exact place. Eventually after the 10th attempt the receiver no longer powers on. I have the original sd card that came with the 9xr pro and followed the instructions carefully.
Did you try with another sd card? I have bought another r-xsr but don't want to risk breaking this one and I have no access to a Taranis.
Thanks
Did you try with another sd card? I have bought another r-xsr but don't want to risk breaking this one and I have no access to a Taranis.
Thanks
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Has anyone gotten the the update function working with 9XR pro? I have tried to update various S.Port devices and it never works. Always gets stuck at 0087.
I built new adapter cable too. I am using fully charged 18650 to power the receiver and toggle the power with a switch to initiate the flashing process once the radio starts looking for the device.
I built new adapter cable too. I am using fully charged 18650 to power the receiver and toggle the power with a switch to initiate the flashing process once the radio starts looking for the device.
ABBC3_SPOILER_SHOW
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Anyone have this working now? If so, what 9XR Pro and RX firmware versions are you using?
S500 + Pixhawk 1 clone + Mauch PM + C&T Telemetry adapter + 9XR-Pro (Taranis gimbals)/XJT/X8R
- MikeB
- 9x Developer
- Posts: 17993
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
I can't test this as I don't have a R-XSR.
If you are having problems, please confirm what firmware and revision you are running on the Tx.
Mike
If you are having problems, please confirm what firmware and revision you are running on the Tx.
Mike
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: Turnigy 9XR Pro and FrSky R-XSR Receiver Firmware Update
Cannot find the PDF you refer to. Where is it hiding?SilentException wrote: ↑Wed Jan 03, 2018 8:54 pm Hi,
I tried to use Turnigy 9XR Pro with latest available R221g1 to update firmware on FrSky R-XSR receiver, following the steps from the PDF on this forum. Because of the 12V Vbat on the module pin, I used external power with GND and Vin connected (Vin was with the switch in-between, as per instructions).
GND was also connected to the module pin. The S.Port was connected to the bottom module pin as well.
Anyone with the R-XSR got this working?
The are several videos showing how to with a Taranis.
On the back of the XJT module there are 5 pins, 3 of which look like
Smartport
+ (5v?)
- (ground)
Can these be used to connect to the receiver, instead of the pins in the radio case behind the module?
S500 + Pixhawk 1 clone + Mauch PM + C&T Telemetry adapter + 9XR-Pro (Taranis gimbals)/XJT/X8R