I have a Turnigy 9XR Pro, was using Open TX but have now flashed with ersky9xr firmware done via SD card,
Cannot seem to connect with eePe, all I ever seem to get is this error even though I could connect fine with OpenTx using SAMBA
=================================================================================
Started AVRDUDE
C:/Program Files (x86)/eePe/avrdude.exe -c arduino -p m64 -U eeprom:r:C:/Users/johnb/AppData/Local/Temp/temp.hex:i
=================================================================================
avrdude.exe: ser_open(): can't open device "lpt1": The system cannot find the file specified.
=================================================================================
AVRDUDE done - exit code 1
=================================================================================
Cannot connect via eePe
-
- Posts: 97
- Joined: Fri Sep 08, 2017 6:53 pm
- Country: United Kingdom
- Location: Bordon, Hampshire, UK
- Contact:
Re: Cannot connect via eePe
Don't use Samba. Please check the version of the bootloader you have.
Hold both horizontal trims inwards while turning the radio ON. You should be in the bootloader menu.. What is the version number you see displayed at the top?
João
Hold both horizontal trims inwards while turning the radio ON. You should be in the bootloader menu.. What is the version number you see displayed at the top?
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 97
- Joined: Fri Sep 08, 2017 6:53 pm
- Country: United Kingdom
- Location: Bordon, Hampshire, UK
- Contact:
Re: Cannot connect via eePe
Thanks all fixed, seems i was trying to use eePe rather than eepskye which it all connects now fine, just have to try and transfer all model settings over. Thanks again for your help.
Re: Cannot connect via eePe
You still shouldn't use samba, you don't need it.
Models from openTX are not compatible with ersky9x.
João
Models from openTX are not compatible with ersky9x.
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
- bob195558
- Posts: 2377
- Joined: Sun Dec 16, 2012 7:24 pm
- Country: United States
- Location: New England, Vermont
- Contact:
Re: Cannot connect via eePe
9XR-pro uses erSky9x firmware which needs to use eePSkye on your PC.
Do not use eepe with erSky9x, because eePSkye is what you need to use with erSky9x.
No samba.
Bob B.
Do not use eepe with erSky9x, because eePSkye is what you need to use with erSky9x.
No samba.
Bob B.
Er9x on 9x radio, with Smartieparts Programmer and TelemetrEZ Board.
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).
ErSky9x on Taranis, Sky9x, 9Xtreme radios.
3D-Printing: (https://openrcforums.com/forum/viewforum.php?f=129).