I have a 9XRPro and have used it for some time using Corona tx module and CR8 receivers and no troubles,so I decided to change to DSM2protcol and purchased a Orangerx DSMX/DSM2 TELEMENTRY MODULE for the 9xrpro and this module uses the internal aerial system,also I purchased the standard orangerx dsm2/dsmx module.
I removed the corona module and pluged in the orange telementry module,and nothing happens no light on module and will not bind with dsm2 rx,so decided to try the other standard module I purchased and nothings happens ,same as other module.replaced the corona module and all working with corona rx,so went back to the new modules but will not bind,and no intention of binding.
is there some settings that need to be made on tx?
many thanks for help if you can.
Jeff
binding problems
- MikeB
- 9x Developer
- Posts: 17990
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: binding problems
With the module that uses the internal antenna, try setting the protocol to "DSM2" and the "DSM Type" to "9XR-DSM".
Then to bind, just select the BIND menu option and press MENU LONG.
Mike.
Then to bind, just select the BIND menu option and press MENU LONG.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: binding problems
+Many thanks MikeB all now working and can now bind all my DSM2 rxs.
Advise please my 9xr pro has the version R202 and VER V.3309.mike do I need to upgrade the firmware?i am very hessant to do this as not sure how to do this,i would need a step by step instructions to do this.
Jeff
Advise please my 9xr pro has the version R202 and VER V.3309.mike do I need to upgrade the firmware?i am very hessant to do this as not sure how to do this,i would need a step by step instructions to do this.
Jeff
- MikeB
- 9x Developer
- Posts: 17990
- Joined: Tue Dec 27, 2011 1:24 pm
- Country: -
- Location: Poole, Dorset, UK
Re: binding problems
Lots of manuals for the 9XR-PRO here: http://openrcforums.com/forum/viewtopic ... 575#p79483.
Do you have eepskye installed on your computer?
The update procedure is quite straightforward, and you may test you are doing everything correctly by reading the firmware first.
Mike.
Do you have eepskye installed on your computer?
The update procedure is quite straightforward, and you may test you are doing everything correctly by reading the firmware first.
Mike.
erskyTx/er9x developer
The difficult we do immediately,
The impossible takes a little longer!
The difficult we do immediately,
The impossible takes a little longer!
Re: binding problems
tx working ok and have flown today
I have another question,i wish to use my 9xrpro as master and a 9xr as pupil where can I get a connecting lead for linking the 2 txs
I could make one if I had details
Jeff
I have another question,i wish to use my 9xrpro as master and a 9xr as pupil where can I get a connecting lead for linking the 2 txs
I could make one if I had details
Jeff
Re: binding problems
Any jack to jack 3.5mm mono or stereo audio cable will work..
João
João
My er9x/Ersky9x/eepskye Video Tutorials
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
https://www.youtube.com/playlist?list=PL5uJhoD7sAKidZmkhMpYpp_qcuIqJXhb9
Donate to Er9x/Ersky9x:
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=YHX43JR3J7XGW
-
- Posts: 1844
- Joined: Tue Dec 27, 2011 8:22 pm
- Country: -
- Location: Ottawa
Re: binding problems
Not worth making a cable. An audio cable can be purchased for $5 or so at an electronics store. A mono cable is preferable, as some transmitters don't work properly with stereo.