9XRPRO with opentx firmware no telemetry data

Hardware Support for the 9XR Pro
Post Reply
zeezy
Posts: 4
Joined: Mon Aug 01, 2016 6:13 am
Country: -

9XRPRO with opentx firmware no telemetry data

Post by zeezy » Sun May 14, 2017 9:13 pm

Hi..can someone help me solve the problem.
I flashed 9XRPRO with opentx9xrpro 2.2.0 N367 firmware and can't get any telemetry data.The module is DJT, Rx is D4R-II.Also with the same setup I got telemetry on my Taranis X9D and I got telemetry on 9XRPRO with ersky9x firmware.So the wiring is not a problem.In telemetry screen I choose frsky D cable and inverted option.Did I miss something or it's not supported in opentx firmware yet?

User avatar
MikeB
9x Developer
Posts: 15564
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9XRPRO with opentx firmware no telemetry data

Post by MikeB » Mon May 15, 2017 12:05 am

Try without the inverted option.

Mike.
ersky9x/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

zeezy
Posts: 4
Joined: Mon Aug 01, 2016 6:13 am
Country: -

Re: 9XRPRO with opentx firmware no telemetry data

Post by zeezy » Mon May 15, 2017 6:12 am

MikeB wrote:
Mon May 15, 2017 12:05 am
Try without the inverted option.

Mike.
Tried all combinations without success

zeezy
Posts: 4
Joined: Mon Aug 01, 2016 6:13 am
Country: -

Re: 9XRPRO with opentx firmware no telemetry data

Post by zeezy » Mon May 15, 2017 11:55 am

Any other suggestions anybody?

User avatar
bob195558
Posts: 1836
Joined: Sun Dec 16, 2012 7:24 pm
Country: United States
Location: New England, Vermont
Contact:

Re: 9XRPRO with opentx firmware no telemetry data

Post by bob195558 » Mon May 15, 2017 12:25 pm

Suggestions:
1) Maybe go back to erSky9x to see if D-Series (PPM protocol) DJT telemetry still works when using erSky9x firmware.
2) Purchase the XJT module to be able to try PXX protocol.

Bob B.
ErSky9x on Taranis, Sky9x, 9Xtreme, Er9x on 9x with Smartieparts Programmer with TelemetrEZ Board
(http://openrcforums.com/forum/viewtopic.php?f=95&t=7182).
CR10 3D Printer: (http://openrcforums.com/forum/viewtopic.php?f=85&t=10702)


zeezy
Posts: 4
Joined: Mon Aug 01, 2016 6:13 am
Country: -

Re: 9XRPRO with opentx firmware no telemetry data

Post by zeezy » Mon May 15, 2017 12:45 pm

bob195558 wrote:
Mon May 15, 2017 12:25 pm
Maybe go back to erSky9x to see if D-Series (PPM protocol) DJT telemetry still works when using erSky9x firmware.
Purchase the XJT module to be able to try PXX protocol.

Bob B.
I wrote before that telemetry worked with ersky9x firmware on my 9xrpro using DJT module and D4R-II rx.. just want to get a clue why it's not working on opentx (9xrpro) firmware and 9xrpro.This is just my older setup. My new setups all works on Taranis internal or external XJT module and x4r-sb or xsr using sbus..tnx for comment,Bob

rtaylor
Posts: 2
Joined: Tue May 23, 2017 11:17 am
Country: -

Re: 9XRPRO with opentx firmware no telemetry data

Post by rtaylor » Tue May 23, 2017 11:36 am

9xr pro and djt with with telemetry cable is not working on opentx 2.2.0. I've gone into the source code and the serial port 2 code in the sky9x target is non functional. I suspect it was broken when taranis specific changes were made. I've fixed some at least gotten rssi to work but I need to polish the code a before I make a pull request. I could be a while.

Post Reply

Return to “Turnigy 9XR PRO radio”