<20m range using 1W OrangeRX TX w/Flyton RX

OpenLRSng runs on a number of different platforms. Find out more / post your questions here.

Moderator: kha

Post Reply
floatingrock
Posts: 1
Joined: Sun Nov 27, 2016 10:03 pm
Country: -

<20m range using 1W OrangeRX TX w/Flyton RX

Post by floatingrock »

I've spent the whole day today trying to get RC to work properly on my system but I'm now out of ideas.. any help would be greatly appreciated.

My equipment:
- Turnigy 9XR Pro Transmitter
- OrangeRX 1W 433MHz TX - https://hobbyking.com/en_us/orangerx-op ... tible.html
- Flytron RX v2 100mW RX - http://www.flytron.com/openlrs/146-open ... er-v2.html
- APM 2.6

Firmware:
- OpenLRSng OrangeRX TX v3.8.8 for TX
- OpenLRSng Flytron RX v3.8.8 for RX
- APM v3.4.0 for APM

The problem:
When I power up the transmitter as I'm standing next to my plane, it works fine. I can move all of the control surfaces and it works great. As soon as the plane starts flying out -- at around 20m -- I lose RC comms with the plane and it crashes to the ground.

Here's a video from this morning:
https://youtu.be/vWRnioX5gwE

You'll notice that I lose comms at about 0:08 in the video, when the transmitter starts beeping.

Here's what I've tried so far:

I suspected an issue with the stock antennas, so I did 2 trials using different combinations of antennas:

Trial #1:
TX: 433Mhz sander antenna
RX: 433Mhz stock HobbyKing antenna
Resulting range of 13 meters before the transmitter lost the signal (!)

Trial #2:
TX: 433Mhz stock HK antenna
RX: 433Mhz stock HK antenna
Resulting range of 7 meters :(

I then switched location, in case there was some sort of interference at 433Mhz:

Trial #3 (at a different location):
TX: 433Mhz HK
RX: 433Mhz HK
Resulting range of 7 meters

I then used a different transmitter/receiver, that uses 2.4Ghz instead:

Trial #4:
TX: 2.4Ghz HobbyKing
RX: 2.4GHz HobbyKing
Distance of several hundred meters (this is a different transmitter, and a different receiver -- works great!)

Ok, back to the 433Mhz system again .. now using the original antenna that came with the OpenLRS receiver:

Trial #5:
TX: 433Mhz HK
RX: 433Mhz OEM antenna
Distance of 16 meters

Oh c**p .. ok, let's see -- I'm using PPM, let me try doing PWM instead (maybe it's some sort of PPM configuration issue):

Trial #6:
TX: 433Mhz HK
RX: 433Mhz HK with PWM instead of CPPM
Distance of 5 meters :(

Ok, this must be some sort of hardware fault. Let me replace the RX module with a new module of the same type:

Trial #7:
TX: 433Mhz HK
RX: 433Mhz HK with different RX module
Distance of 3 meters

Aha, must be the TX then .. let's replace that with a new module of the same kind (OrangeRX TX):

Final Trial #8:
TX: Different 433MHz TX module
RX: 433Mhz HK stock antenna
Distance of 20 meters

Oh dear, I really have no idea what could possibly be wrong at this stage!

Every time I swapped out modules, I would flash the OpenLRSng firmware again (the latest 3.8.8 release) using the Chrome OpenLRSng configurator.

At this point, I'm completely lost as to what to do next. What could possibly be wrong here?

dispetto77
Posts: 2
Joined: Wed Dec 07, 2016 11:19 pm
Country: -

Re:

Post by dispetto77 »

Hi. I got your problems with my first orangerx openlrs module.
It was an hardware issue. The internal antenna cable was damaged and, also, the ground on the antenna pin was closed with a pin on the internal RF module.

It's a known issue.

I solved changing tx module. But the same if changing the internal antenna cable and adding a bit of scotch on the internal RF module pins.

Anyway, my current setup is
- openlrsng tx module 1W with 5-6volts mod (low-high transmission power)
- openlrsng rx module 1W with dipole

And I have great resultsImageImageImage

Inviato dal mio RAINBOW 4G utilizzando Tapatalk
AhmedRehan
Posts: 1
Joined: Wed Dec 05, 2018 7:35 pm
Country: -

Re: <20m range using 1W OrangeRX TX w/Flyton RX

Post by AhmedRehan »

Hi
How you binded the RX and Tx module.
User avatar
User66whytho
Posts: 1
Joined: Fri Jan 04, 2019 1:12 am
Country: -

Re: <20m range using 1W OrangeRX TX w/Flyton RX

Post by User66whytho »

i too have the 1w olrs units from yrs ago, i had poor results, after just 200m or so the plane lost signal.
but i still love the tx rx pair even tho ive not used them since.
'FPV is not just a hobby, it is a way of life'
ilgnav
Posts: 1
Joined: Thu Sep 15, 2022 8:33 pm
Country: -

Re: <20m range using 1W OrangeRX TX w/Flyton RX

Post by ilgnav »

How i can bind this tx/rx?

Post Reply

Return to “OpenLRSng hardware”