Flash with bootloader verification error

Support and help for the OpenLRSng project.

Moderator: kha

Post Reply
Morphin
Posts: 4
Joined: Mon Jan 20, 2014 7:46 am
Country: -

Flash with bootloader verification error

Post by Morphin » Sun Nov 06, 2016 4:27 pm

Hi
I try to flash the -bl hex with avrdude:


avrdude -b 19200 -c usbasp -p m328p -P USB -v -D -F -u efuse:w:0x05:m -u hfuse:w:0xDE:m -u lfuse:w:0xFF:m -U flash:w:RX-5-bl.hex:i


Error:

avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0106
0xc2 != 0x42
avrdude: verification error; content mismatch

Any hints?

THank you very much
Andy


Here the whole output:


avrdude: Version 5.10, compiled on Jan 19 2010 at 10:45:23
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

System wide configuration file is "C:\AVR\bin\avrdude.conf"

Using Port : USB
Using Programmer : usbasp
Overriding Baud Rate : 19200
AVR Part : ATMEGA328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 5 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f
avrdude: reading input file "RX-5-bl.hex"
avrdude: writing flash (32768 bytes):

Writing | ################################################## | 100% 20.24s



avrdude: 32768 bytes of flash written
avrdude: verifying flash memory against RX-5-bl.hex:
avrdude: load data flash data from input file RX-5-bl.hex:
avrdude: input file RX-5-bl.hex contains 32768 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 16.75s



avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0106
0xc2 != 0x42
avrdude: verification error; content mismatch

avrdude done. Thank you.

Post Reply

Return to “OpenLRSng”

Who is online

Users browsing this forum: No registered users and 1 guest