Hi, my name is Bob and I am a new user to OpenRc. It has been about 40 years since I did anything with radio control and things sure have changed since then.
Just to give you an idea of my capabilities, I had a very serious Stroke back in 2002 which they said I should not have survived. Nothing on the right hard side works now, apart from that I am fine. Anyway I have decided to give Open TX a try using a FlySky 9X V2 transmitter with the aim of getting it to control a hexacopter, https://www.youtube.com/watch?v=OsATmfRC0U4 something like this would be nice.
I started by installing the HK backlight kit and began soldering wires to the board for the programming set up. That got a little bit fiddly and in the end I decided not to do it that way and saw that there was a Smartieparts board available by email so I went and got one.
That was a very well made board and certainly worth the investment cost. It went together like it was made for it cut the wires for the backlight and soldered them to the smartieparts connector and it works too.
Then I did a bit of reading and video viewing to make sure I had it correct.
Because I use a Mac I went and got Open TX configured and Companion software and flashed the 9X with Open TX after I turned the power ON (common trap I believe). I have noticed that the trim switch is not working properly for the Aileron, looks like I have to take it apart again. Exercised it a bit and now it is working. The only other things to come now are the FrSky modules, the hex is already built.... Not long now.
Big thanks to Steven, I didn't have to call
If I can do it, anyone can.....
It Works!!
Everything about the smartie programmer and backlight kit!
Return to “SMARTIEPARTS PROGRAMMER”
Jump to
- OPENRC News & Information
- ↳ General Information & Rules
- ↳ Feedback
- General help and information
- ↳ Software
- ↳ Hardware
- ↳ General help (FrSky Taranis radio)
- Open Radio Control Transmitter Firmwares
- ↳ General model setup questions
- ↳ er9x / gruvin9x / th9 based firmwares
- ↳ Template Library
- ↳ Splash Screen Library
- ↳ Helicoptor Programming
- ↳ radioclone
- ↳ stock firmware (fly sky th9x)
- ↳ Template Library
- ↳ Sound Pack Library
- ↳ Edge TX
- ↳ openTx
- ↳ openTx for FrSky radios
- ↳ openTx model setup
- ↳ er9x
- ↳ er9x model setup
- ↳ ersky9xr
- ↳ erskyTx (was ersky9x)
- ↳ ersky9x model setup
- ↳ gruvin9x
- ↳ gruvin9x model setup
- ↳ th9x
- ↳ th9x model setup
- ↳ gv9x
- ↳ radioclone
- ↳ radioclone model setup
- ↳ tgy9xr
- ↳ tgy9xr model setup
- ↳ AR-T6
- ↳ other
- Desktop Software to Program Your Transmitter
- ↳ eePe
- ↳ companion9x
- ↳ eepSKYe
- Open Radio Control RF Systems & Hardware
- ↳ OpenLRS
- ↳ OpenLRSng
- ↳ OpenLRSng hardware
- Closed Source Radio Control RF Systems & Hardware
- ↳ Royal Way - Rlink UHF Long Range System
- Transmitter Hardware
- ↳ FlySky TH9X / Turnigy 9X / Eurgle 9X radio
- ↳ SMARTIEPARTS PROGRAMMER
- ↳ HARDWARE MODS & HACKS
- ↳ FRSky Telemetry Mods
- ↳ ArduPilot Mods
- ↳ Electronic Mods
- ↳ Hardware Mods
- ↳ Soldering, Hardware, Skills
- ↳ DSM2/DSMX Mods
- ↳ UPGRADE BOARDS
- ↳ sky9x upgrade board
- ↳ gruvin9x upgrade board
- ↳ 9Xtreme upgrade board
- ↳ RF MODULES
- ↳ The FRSKY Forum
- ↳ PROGRAMMERS
- ↳ FrSky Taranis radio
- ↳ FRSky Horus radio
- ↳ Turnigy 9XR PRO radio
- ↳ Orange DSM Telemetry module
- ↳ Turnigy 9XR radio
- ↳ PROGRAMMERS
- ↳ Other Radios
- ↳ Retro Radios
- Other OPEN Projects
- ↳ General RC Electronic Projects and Discussion
- ↳ OpenXVario - an open source vario supported by the open source firmwares!!
- ↳ Other Electronic Projects
- ↳ OpenFlightStab
- ↳ OpenLRSng
- ↳ 3D Printing
- Other Forums
- ↳ The Pickled Gnu (The Pub)
- ↳ FPV Projects
- ↳ Reviews
- ↳ Where to buy / Spares / Modules? Selling up?
- Links
- ↳ er9x on Google Code
- ↳ ersky9x on Github
- ↳ Gruvin9x on Google Code
- ↳ th9x on Google Code
- ↳ openTx on Google Code
- ↳ gv9x on Google Code
- ↳ radioclone on Sourceforge
- ↳ eePe on Google Code
- ↳ companion9x on Google Code
- ↳ 9X Guides
- ↳ openxvario