9xr Pro blade 350qx transmitter format, anyone have the set up?

Post Reply
User avatar
WoodsyOwl
Posts: 5
Joined: Tue Mar 28, 2017 11:09 pm
Country: -

9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by WoodsyOwl » Tue Mar 28, 2017 11:22 pm

I need help programming my Turnigy 9xr Pro for my blade 350qx does anyone have the transmitter set up? I have searched far and wide in YouTube land and even HobbyKings site but can't seem to find a template to just copy, I am a noob with open TX transmitters so I really want to find something I can use with the existing ersky9x firmware without having to download anything but I am starting to wonder if that's even possible? Any help would be greatly appreciated!


Sent from my iPhone using Tapatalk

User avatar
MikeB
9x Developer
Posts: 15528
Joined: Tue Dec 27, 2011 1:24 pm
Country: -
Location: Poole, Dorset, UK

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by MikeB » Wed Mar 29, 2017 3:53 pm

Have a look at this thread: https://www.rcgroups.com/forums/showthr ... ade-350-Qx.

While the settings are shown as for er9x, ersky9x should use the same settings.

Mike.
ersky9x/er9x developer
The difficult we do immediately,
The impossible takes a little longer!

User avatar
WoodsyOwl
Posts: 5
Joined: Tue Mar 28, 2017 11:09 pm
Country: -

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by WoodsyOwl » Wed Mar 29, 2017 4:17 pm

MikeB wrote:Have a look at this thread: https://www.rcgroups.com/forums/showthr ... ade-350-Qx.

While the settings are shown as for er9x, ersky9x should use the same settings.

Mike.
Thank you Mike, I will check this out!


Sent from my iPhone using Tapatalk

User avatar
WoodsyOwl
Posts: 5
Joined: Tue Mar 28, 2017 11:09 pm
Country: -

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by WoodsyOwl » Thu Mar 30, 2017 10:32 pm

Well I guess I need it spelled out a bit more, while this was helpful I am a novice with these remotes so the search continues I am learning a ton as I go along which is good though


Sent from my iPhone using Tapatalk

User avatar
WoodsyOwl
Posts: 5
Joined: Tue Mar 28, 2017 11:09 pm
Country: -

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by WoodsyOwl » Wed Apr 05, 2017 12:12 pm

I finally figured it out!, what a happy night, turns out I was over complicating "everything" if anyone see's this and is having similar issues being a newb you need to just focus on the basic (mixes) everything else is taken care of by the on board flight electronics, yes you can tweak things as you learn more about the controller but do not let it make your brain explode to get it in the air and flying just focus on channels 1-4 and assigning your trainer switch to channel 6, you can worry about expo, curves etc.... later as you learn


Daedalus66
Posts: 1767
Joined: Tue Dec 27, 2011 8:22 pm
Country: -
Location: Ottawa

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by Daedalus66 » Wed Apr 05, 2017 12:40 pm

Congratulations! The secret is in identifying the fundamentals.

User avatar
WoodsyOwl
Posts: 5
Joined: Tue Mar 28, 2017 11:09 pm
Country: -

Re: 9xr Pro blade 350qx transmitter format, anyone have the set up?

Post by WoodsyOwl » Wed Apr 05, 2017 12:45 pm

Thank you!

Post Reply

Return to “ersky9x model setup”